IPDB › China Industry › Manufacturing & Processing Machinery
China, Chinese Vertical Centrifuge Machine for Material Dewatering1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
Mineral SeparatorRefrigerated CentrifugeSludge Dewatering
CITICIC Luoyang Heavy Machinery Co., Ltd.
Preview:
Product Description Introduction:The vertical centrifuge is made up with the screen which diameter range from 700 to 1,000 mm , the rotor body (including the blade), transmission, body, lubrication system etc. Application:The vertical centrifuge is fit for material dehydration, generally used for coal, salt and other materials. Working Principle:Wet materials are feed into the mouth of centrifuge, then are accelerated by the rotated distribution cone and move rapidly towards the space between screen and rotor. With the centrifugal force, the smaller particles of material get closed to the screen surface, liquid and part of the particle size of less than 0.5mm of material get across the material space and screen gap, then are thrown out of the screen, the larger particles of materials soon slipped into spiral nesting mouth along the screw blade with the action of gravity and centrifugal force fine material attached to the screen surface are discharged by the scraper centrifuge through blade action, while the liquid through the screen and fine materials are thrown into the water tank then outflow through the drain, so as to achieve a solid-liquid separation. Technical Performance Parameters:Serial No.Part NameUnit.Numerical Value1Feed sizemm0~252The screen cloth works aream21.883Handling capacity per hourt/h140~2004The percentage of product water discharge%5~85Strainer big end diametermm12006Strainer slitmm0.5 Main electrical machineryModelY280S-4-V17Powerkw75 rotating Speedr/min1480 Lubricates the electrical machineryModelY90L-48Powerkw1.5 rotating Speedr/min14009External dimensions Long × wide × highmm3160 × 2460 × 268010Gross weightkg9121 Installation And Testing:When the centrifuge is assembled completely in the manufactory, the test should be carried out in air operations. It should be sent out to the users in the form of machine after it is up to the requirements, the users can directly follow the steps to install the equipment when they get receipt of it.1. Installation Step1) Check whether the basis of surface is level, if it is uneven, adjust the leveling pad. Check the ground pin-hole size and pore size of the centre. Check whether the basis of elevation to meet the requirements.2) Mount the shock absorber to the ground pin holes, install the nut first but not tightened until the machine is in the right place, then solid-tight.3) Hoisting the machine in the place, tighten anchor bolts, tighten the upper pairs of nuts before the measurement with the caliper pad diameter, it is required that the diameter of compact size should be increased 2~3mm than the first fasten one. 2. Test Step1) Checked before testing itemsa. All bolts connections should be tightenb. There is no equipments which have effects on the machine operation.c. Make sure the pulley can be moved with both hands so that the machine can be rotated flexibly with non-stuck and abnormal noise.d. Make the belt hang right.e. Indicator within the oil tank should be located in the groove between the upper and lower limits.2) Commissioning and inspection of the projectMeet the above requirements, follow these steps, and start running in the air for 8 hours.a. Open the oil pump motorb. Observe the oil supply situation, make sure everything is ok, open the console.c. While there is no abnormal noise, stable operation, measure the amplitude of the centrifuges in the horizontal plane and make sure that it is less than 0.3mm.d. Measure the oil temperature every 30 minutes, ensure the oil temperature rising is no more than environmental temperature-30oC.3) Loading TestWhen all functioning of the machine working in the air is normal, then gradually feeding at the same time pay attention to the functioning of the device, while there is no abnormal phenomenon, the handling capacity can be increased to150~200t/h, the handling capacity of the material easily dehydrated can be larger, difficult to dehydration material handling capacity can be smaller. Add enough materials, it may take the measurement as the following items, when all meet the requirements, the equipment can be put into use.a. Checked by commissioning and inspection itemsb. Measuring capacityc. Moisture measurement productsd. Measurement original compound, the content of grain size of less than 0.5mme. Measurement of centrifugal fluid solidsf. Measuring power consumption Operation And Maintenance:1. Operation1) Pre-drive checksa. Check the machine whether in full state and the connectors are loosening.machine and the oil spill out of the pipeline.c. Moving the pulley, check whether the machine is resisted and the belt tensioning situation.d. Check whether the oil level inside the tank between the upper and lower limits of the oil indicator, enable the pipeline junction leakage are prohibited.2) Drivinga. Activate the pump motor, to observe the oil flow table.after the oil flow through 1~2 minutes, then start the main motor.b. When the machine is running in the normal condition, begin to feed, the charging capacity should be gradually increased.3) Parkinga. Stop feeding, get the closure of the host after 2~3minutes.b. Shut main motor down after half a minute, and then close the pump motor. 2. MaintenanceCentrifuge normal maintenance plays an important role in preventing accidents and injury in the weight of link components in the device's using, and the systems should be required to perform.1) Lined lid is easy to wear and tear, open the lid or observe the lid abrasion situation from the observation hole, if the abrasion is serious, it should be replaced promptly.2) Distribution cone is mounted on the top of the rotor body, contacted with material directly and easy to wear and tear. Every time when you change the screen and scraper, pay attention to check the distribution of the remaining tapered wall thickness, if it is too thin, take replacement timely.3) Screen is the key part of the centrifuge, it is forbidden that there is no wire, wood, bolts and debris in the machine while it is used. For a long time using, if a little screen surface was damage, it allowed to be repaired by welding, but if the gap in the screen is as large as 0.75mm wear or screen seriously worn, the screen should be replaced. Likewise, if the mesh repair welding area is too large, re-do before the use of dynamic balance.4) Spiral scraper, it should be paid attention to adjust the gap between blade and the screen surface when it is working, usually 0.3~1.5mm.If the gap is too large, it can mount the adjustment pads on the top of the rotor body underside for each additional pad, the gap decreased 0.34mm.If the adjustment of all cushion mount to the lower part, the gap remains large, replace the blade. It should pay attention to the pairs of containers while changing scraper, mount the weight of two scraper into a symmetrical position to keep the rotor body balancing performance. After replacement of the scraper, the machine should be conduct and test run in the air operation. If the rotor vibration is too large, it would have to do the rotor body balancing.5)Export the protection lining, materials get through the lower scraper with the influence of centrifugal force, the material is left out in the protection of lining, and then fall until the belt exit cone machine, it should pay attention to the protection liner wear circumstances from the hole observed when it is used. When serious damage happened, replace it timely.6) The export cone is at bottom of the machine, when material falls, the cone inner surface is often worn in use, and the lining should be checked regularly. If there is some damage, it must be promptly replaced.7) The differential is a driving part of the machine, it should be aware of the lubrication conditions when it is used. It should pay attention to whether the oil is spilled, oil flow table is oil flow and the differential pulley-side and the upper part of bell-shaped cast-side sealing department have leaked oil. Enable that there is not any unusual noise in the working differential.8) Lubrication system. It should be always checked the oil spill situation, pressure gauge and oil flow sheets. Oil filters in the filter and the oil tank strainer should be periodically cleaned or replaced. The oil level in the fuel tank must be within the upper and the lower limits shown in the table.9) Cleaning the materials inside the machine regularly, rinsing the materials between the hood and lining surplus with red bell-shaped water, cleaning the appearance of the machines and the places around the equipment, make sure it is working in good condition.
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...