IPDB › China Industry › Industrial Equipment & Components
China, Chinese 80mm*1.6*1.4/2 Bandsaw Blades /Superalloy/Titanium Alloy Cutting Band Saw Blades1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
Industrial Saw BladeTCT Band Saw BladeBandsaw BladeBand Saw
Shaoxing Shangyu Hante Machinery Equipment Co., LTD.
Preview:
Product Description High quality Carbide Tipped band saw blades listSpecificationsTeeth Form27mmx0.91x.0353/4 2/334mmx1.11-1/4x.0423/4 2/341mmx1.31-1/2x.0503/4 2/3 1.7/2.5 1.4/2 1/1.5 0.75/1 0.75/1.2554mmx1.62x.0633/4 2/3 1.7/2.5 1.4/2 1/1.5 0.75/1 0.75/1.2567mmx1.62-5/8x.0632/3 1.7/2.5 1.4/2 1/1.5 0.75/1 0.75/1.2580mmx1.63x.0632/3 1.7/2.5 1.4/2 1/1.5 0.75/1 0.75/1.251,High hardness, high red hardness, high wear resistance;2,It is difficult to cut the metal materials, such as titanium alloy, stainless steel, hardened steel, raw material paste, nickel base alloy, cast steel, etc., can be cut freely;3,Unique tooth shape design, with excellent chip removal performance;4,Saw back refining technology, improve the fatigue strength of band saw.Chemical composition of cemented carbide: (C)(Si)(Mn)(P)(S)(Cr)(Mo)(V)(W)(Co)cemented carbide Co:10% Residual refractory metal carbides:Wc,Tic,Nbc,Tac,VcHGS400.40 0.30 0.45 0.015 0.005 3.00 1.50 0.25 Cutting fault analysis : projectcutting elementsband brokingsawing deviationsawtooth cracksurface roughsawtooth wear too fastcutting vibrationAdjusting the sawing machinetwo guide rods should be located close to the workpiece guide block is wearing parts, must be regularly checked and timely replaced.The broken belt guide block is worn or the adjustment distance is too largeThe broken belt guide block is worn or the guide rod is loosening or shaking the cutting vibration guide block is not well adjustedAdjust the driven pulley to achieve the smooth operation of saw blade without dropping, stringing and biting the stop of the pulley.the belt wheel is badly worn The iron brush used to remove sawdust is a vulnerable part. It should be checked and replaced in time. The iron brush is damaged, and the saw belt groove is blocked by cutting debris The iron brush is damaged and cannot work properly Adjust the driven pulley to have proper tension. For the saw belt used for a long time, the tension should be compensated and correctly matched with the concentration of cutting fluid (coolant).saw belt tension too highsaw belt tension too low saw saw belt tension too lowCorrectly mix the cutting fluid (coolant) concentration too low cutting fluid (coolant) or too low coolant concentration cutting parametersCorrect selection of saw band linear speed saw band linear speed too low saw band linear speed too lowsaw band linear speed too lowcarefully adjusted saw band linear speedcorrectly Choose saw feed line ratesaw band feed ratetoo largesaw band feed ratetoo largesaw band feed ratetoo largesaw band feed ratetoo largesaw band feed rate too large or too smallsaw band feed rate too large or too smallBand saw blade selectionaccording to the characteristics of the workpiece to be cut, the tooth shape and the specification of the saw band are correctly selectedtooth saws too smaltooth saws too smaltooth saws too smaltooth saws too smaltooth saws too smal and the new saw band is used, the initial running-in is needed, the parameters are gradually increased from low speed and slow feed, For maximum service life band saws no running or running time shortband saws no running or running time shortband saws no running or running time shortDo not forcibly use Saw bands that have exceeded their service life sawtooth worn and scrapped sawtooth worn and scrapped According to the characteristics of the workpiece to be cut, correctly select the tooth hardness tooth hardness Over smaltooth hardness over small tooth hardness over small The cut artefactObserve the working surface for defects and inclusion of sand sand or rust Poor workpiece surface, to cut into a bunch of workpiece, ensure correct clamping method the workpiece moves during cutting process improper clamping of workpieceTop appliance:Application Scenario: A corner of the workshop:Packaging and Shipping:Factory Tour:Shaoxing Shangyu Hante Machinery Equipment Co., LTD is specialized in producing bimetal saw blades, carbide band saws, food saws, woodworking alloy saws and selling high-speed circular saws, saws and circular saws. Our advantage:1. Factory with 25 years of experience in the production of bimetallic band saw blades2. Products have been exported to more than 60 countries and regions3. All products have been strictly tested and quality assurance is provided4. Provide after-sales service support5. Main products: bimetal band saw blades, carbide band saw blades, high-speed circular saw machines, sawing machines, food processing machinery.
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...