IPDB › China Industry › Chemicals

China, Chinese Research and Optimization of Single-Stage and Two-Stage Gasifier Systems for Efficient Gasification and Industrial Applications¹ Industrial Products Supplier Manufacturer Details, price list catalog:

China Industrial Products Supplier Manufacturer List Catalog

Gas Generation Equipment Parts Other Gas Generation Equipments Parts Gasifier Two-Stage Gasification

Shanghai Prime Metallurgy Technology Co., Ltd

Preview:

Product Description Product DescriptionPart 1 List for EquipmentsList for Main Equipments of φ 3.2M Two-section Cold Gas Station (One Working, No Standby) No.Item Spec. & main parametersQty.Remarks totalstandby 01Coal hoistV=1m3/time, 10m3/h4 2t hoist02Coal feeding mechanismHydraulic top inserted plate and bottom bell jar 5 PLC programmatic control03Main body of gas producerφ32005 04Producer lining 5 05Steam collecting drumφ15005 06Air check valveDN4005 07Natural suction valve φ2505 08Bell type valveDN3005 09Cyclone dust collectorφ20005 Internal insulation10Forced air cooler32Pcs5 11Cyclone detarring deviceφ12005 12Electro detarrerC-395 Including power supply13Plate-shell heat exchanger F=1500m25 14Electrostatic dust collectorC-725 Including power supply15Air blowerP=110KW21 16Gas boosterP=160KW21 17Soft water tankφ2000×18005 18Condensate pump for tar, light oil50YW15-163 20Centrifugal pumpIS150-125-315,P=30KW31 22Worm gear wafer butterfly valveDN250 D371X-141 23Butterfly valveDN500151Inlet of booster24Butterfly valveDN30061Outlet of booster25Butterfly valveDN35061 26Electrical instruments Including 6 frequency converters27Installation materials 28Fees for guiding the installation and commissioning Part 2 Project ProfileA Basis of design, manufacturing and installation1. GB50195-94 - 'Code for design of producer gas stations'2. GB6222-2005 - 'Safety code for gas of industrial enterprises'3. The coal for gasification should conform to the standard of (GB/T9143-2001).4. The technical parameters and requirements provided by the customer.B Selection basis of gas producerThe customer will propose to install Ф3.2m two-section type gas producer, five (5) sets, to produce the energy for production. Considering the coal quality in India, the gas production forФ3.2m two-section type gas producer will be 5500~7000Nm3/h per producer, and the calorific value of gas will be not less than 1350kcal/Nm3 to ensure 8000h/a of continuous production. When the load for stable operation of the gas producer is at about 85%, it will be convenient for the operation and management of the gas station and benefit the service life of the equipment.B1 Design principles:1. Select advanced, mature, and reliable technology and equipment.2. The technological proposal can fully meet product requirements and environmental protection requirements.3. Ensure rationality of process and stability of long-term operation.4. Combination of practice and saving investment.B2 Advantages of two-section gas producer:1. Relax the standard of coal for gasification charging into the producer.2. Compared with a one-section gas producer with corresponding dimensions, the calorific value of gas could be increased by about 10%.3. The gasification efficiency will be about 5% higher than that of a one-section producer.4. The tar generated for recovery is light tar, which has good fluidity, easy to deliver, and has high utility value.5. Strong ability to adapt to the change in load, and furnace condition is stable, labor intensity is lower.6. The processing system is simple, and the equipment is compact and the floor space is less.7. The environment for operation and in the station area is better than that of a one-section producer.8. The raw material for gasification is bituminous coal, and the economic benefit is good.C Reference table for the content of each component of producer gas (bituminous coal for firing)Item Volumetric component of dry gas(%)Density(kg/ Nm3)LHV(KJ/Nm3) CO2+H2SO2CmHnCOH2CH4N2 %3~70.1-0.30.2-0.425-3011-151.5-347-541.1~1.135020~6280Remark: The coal for gasification should abide by ' Quality standard of the coal for gasification of Atmospheric fixed bed gas producer' (GB9143-2001); Please abide strictly by this standard to avoid problems occur during operation in the future.Part 3 Gas producing principle and process description1. Gas producing principle of two-section gas producer:A gas producer is divided into an ash layer, oxidation layer, reduction layer, dry distillation layer and dry layer. The gasification agent (air + steam) is sent into the producer from the bottom of the producer, there will have the following chemical reactions in oxidation-reduction layer: C+O2=CO2+Q C+CO2=2CO-Q C+H2O=CO+H2-Q C+2H2O=CO2+2H2-Q CO+H2O=CO2+H2+Q2. Process descriptionUse coal hoist to feed the coal into the coal bin, and feed the coal into the chamber of gas producer via stoker. After that the coal will carry out drying and dry distillation in dry distillation section of the gas producer. The coal will move down slowly with the temperature rising gradually, and then arrive at gasification section after 10-12 hours. In dry distillation section, the heat generated by part of ascending gas in gasification section will release the moisture in the coal, tar and most of sulfide will also be dry distilled out, and then the hydrocarbon will be generated which will form the top gas with part of ascending gas in the gasification section. The semi-coke shape coal char entering gasification section will produce the gas after gasification reaction. One part of the gas produced will go upwards to dry distillation section, and another part will form lower gas in the gasification section.The top gas will leave gas producer and enter into electro detarrer after passing through cyclone detarring device to remove the tar carried by gas, and then mix with lower gas.After most of dust is removed by cyclone dust collector, the lower gas will enter into the air cooler through the wet disk valve. After air cooling, the gas temperature will be decreased to about 150-180oC from 400-500oC, and then mix with the top gas.The mixed gas will enter the electrostatic dust collector to remove the dust and light oil in the gas, and be cooled further to normal temperature through indirect cooler.The mixed gas will be delivered to the desulfurization system to remove the sulfur after pressure increasing by gas booster, and then the clean gas will be conveyed to kiln for use at last. The coal tar, light oil and condensate separated from the electro detarrer, electrostatic dust collector and scrubber will enter into the separating pond. After separating, the coal tar and light oil can be supplied externally, and also can be used with condensate together as fuel for boiler. The condensate also can mix with pulverized coal to make into coal water slurry for fuel use.3. Final indexes of gas:Gas output : 5500-7000Nm3/hGas Calorific value: ≥6061 KJ/Nm3Dust content in gas: ≤25 mg/Nm3Tar content in gas: ≤20 mg/Nm3H2S content in gas: ≤50 mg/Nm3Gas temperature at station outlet: 35~45oC Part 4 Brief description for structure of gas producer and technical parameters1. Advantages of two-section producer:1) Compared with a one-section gas producer with corresponding dimensions, the calorific value of gas could be increased by about 10%.2) Produce two types of gas with different heat values, which can use separately or in mixed-use.3) Two-section producers can recover the tar and light oil.4) The coal varieties can be loosened appropriately.2. Structure of φ3.2m two-section producer:1) StokerThe stoker will adopt hydraulic drive, which is the coal feeding device with the structure that a rotary drum on top, inserted plate in the middle and a bell type at the bottom. This kind of structure could effectively avoid gas leakage. During coal feeding, firstly the bottom bell is closed, the middle inserted plate is open when the top rotary drum is open, the coal will be fed into the stoker from the feed bin depending on the self-weight of the coal, and then the top rotary drum is closed, and the middle inserted plate is also closed at the same time, and the bottom bell is open, all the coal will fall into the producer, finally bottom bell is closed, thus a coal feeding cycle is completed. The coal feeding process can realize PLC programming automatic control.2) Main body of producerThe main body of producer consists of refractory bricks, water jacket, grate, base disc, inlet bellows, etcThe dry distillation section will be laid by high quality refractory bricks. The material for inner ring plate of water jacket will select 20g, and Q235-A for outer ring plate, so as to ensure enough safety for gas station. The water jacket is connected with steam header, the natural circulation system of softened water is formed from up and down. The softened water goes into the steam header at first, and then descends into the water jacket from steam header. The water-vapour mixture is generated after heating, and goes to the steam header via riser pipe. The steam separated by water separator will be used as gasification agent. Only when supply of softened water stops for temporarily maintaining the production, the water used in water jacket could be allowed to use running water for a short period.The base disk consists of ratchet wheel and ash disk. The ratchet wheel and grate are fixed on the base disk. The grate installed by our company was produced through years of research and design, so as to ensure uniform distribution of air at gas producer bottom; and ash removal on both sides also could avoid the offset during gas producer's operation and reduce the air blasting resistance, therefore reduce the carry-away matters, it benefits for the purification of gas. The antifriction bearing is installed below the ash disk, the grate is turning at the time when the ash disk is rotating, the ash residue will fall into the ash disk. The ash residue will be broken by small ash knife and be removed out of the ash disk by big ash knife. The inlet bellows in middle and water seal circle below the ash dish will form the water sealing.3. Ash removal deviceThe main body of a producer consists of refractory bricks, water jacket, grate, base disc, inlet bellows, etc.The dry distillation section will be laid with high-quality refractory bricks. The material for the inner ring plate of the water jacket will select 20g, and Q235-A for the outer ring plate, to ensure enough safety for the gas station. The water jacket is connected to the steam header, and the natural circulation system of softened water is formed from up and down. The softened water goes into the steam header at first and then descends into the water jacket from the steam header. The water-vapour mixture is generated after heating and goes to the steam header via a riser pipe. The steam separated by the water separator will be used as a gasification agent. Only when the supply of softened water stops temporarily maintaining the production, the water used in the water jacket could be allowed to use running water for a short period.The base disk consists of a ratchet wheel and an ash disk. The ratchet wheel and grate are fixed on the base disk. The grate installed by our company was produced through years of research and design, to ensure uniform distribution of air at the gas producer's bottom; ash removal on both sides also could avoid the offset during the gas producer's operation and reduce the air blasting resistance, therefore reduce the carry-away matters, it benefits for the purification of gas. The antifriction bearing is installed below the ash disk, the grate is turning at the time when the ash disk is rotating, and the ash residue will fall into the ash disk. The ash residue will be broken by a small ash knife and removed from the ash disk by a big ash knife. The inlet bellows in the middle and the water seal circle below the ash dish will form the water sealing.The main body of a producer consists of refractory bricks, water jacket, grate, base disc, inlet bellows, etc.The dry distillation section will be laid with high-quality refractory bricks. The material for the inner ring plate of the water jacket will select 20g, and Q235-A for the outer ring plate, to ensure enough safety for the gas station. The water jacket is connected to the steam header, and the natural circulation system of softened water is formed from up and down. The softened water goes into the steam header at first and then descends into the water jacket from the steam header. The water-vapour mixture is generated after heating and goes to the steam header via a riser pipe. The steam separated by the water separator will be used as a gasification agent. Only when the supply of softened water stops temporarily maintaining the production, the water used in the water jacket could be allowed to use running water for a short period.The base disk consists of a ratchet wheel and an ash disk. The ratchet wheel and grate are fixed on the base disk. The grate installed by our company was produced through years of research and design, to ensure uniform distribution of air at the gas producer's bottom; ash removal on both sides also could avoid the offset during the gas producer's operation and reduce the air blasting resistance, therefore reduce the carry-away matters, it benefits for the purification of gas. The antifriction bearing is installed below the ash disk, the grate is turning at the time when the ash disk is rotating, and the ash residue will fall into the ash disk. The ash residue will be broken by a small ash knife and removed from the ash disk by a big ash knife. The inlet bellows in the middle and the water seal circle below the ash dish will form the water sealing.The ash removal adopts double ash knives. The ash is cleaned on both sides, and the ash is evenly discharged, which can effectively prevent the partial operation of the furnace caused by the uneven ash discharge. The provided ash knives are bi-directional spiral surface tire punching coil forming, which can effectively reduce the ash discharge resistance. The ash removal machine is driven by hydraulic pressure and has a ratchet pawl structure. When cleaning dust, the hydraulic station controls the swing hydraulic cylinder to reciprocate, so that the pawl drives the ratchet wheel to complete the stepping of the ash tray to achieve the purpose of dust removal. The cleaning speed of the ash removal machine could realize stepless speed regulation by adjusting the one-way throttle valve of the hydraulic station. Compared with the worm gear structure, the cleaning driving force of this structure all acts on the tangential direction of the ratchet, with no excess power loss, high mechanical efficiency, and no radial runout, extending the service life of the ratchet.Part 5 Selection of Major equipments in gas station1. Gas producing and purification section1) Gas producerFeature:two-section type, feed coal discontinuously by hydraulic top inserted plate and bottom bell, ash removal through hydraulic driving the ratchet wheel and pawl.Function: the coal reacts in this equipment under the action of gasification agent (air, steam), and produce qualified gas.Specification:YM3.2Qty.: 5 sets2) Cyclone dust collectorFunction:pre-remove the dust in lower gas.Specification:φ2000 typeQty.: 5 setsGas processing capacity:4000 Nm3/h·setDust collection efficiency:60~80%3) Forced air coolerFunction:decrease the gas temperature upto 150-180oC from 400-500oC by means of indirect contact between air and gas.Specification: 32 pipesQty.: 5 sets Gas processing capacity:6500 Nm3/h· setGas inlet temp.:400~500oCGas outlet temp.:150~180oC4) Cyclone detarring deviceFunction:pre-remove par of tar in top gas, so as to relieve the working burden of electro detarrer.Specification:φ1200 typeQty.:5 setsGas processing capacity:3000 Nm3/h·setDetarring efficiency:60-80%5) Wet disk valveFunction:cut off lower gas with system when failures or maintenance.Specification:φ1000 typeQty.:5 sets6) Electro detarrerFunction:catch and remove the tar in top gas, to ensure the cleanness of gas.Specification:C-39 typeQty.:5 setsGas processing capacity:2500Nm3/h·setGas flow rate: 0.71m/sDetar efficiency:98~99%7) Electrostatic dust collectorFunction:carry out secondary detarring and dedusting after top and lower gas mixing here.Specification:C-72 typeQty.:5 setsGas processing capacity:6500 Nm3/h·setGas flow rate:0.93m/sDedusting efficiency:95~97%8) Indirect coolerFunction:top and lower gas will mix here. Under the condition of not directly contacting with cooling water, the gas temperature will be decreased to precipitate the condensate in the gas with the saturation temperature drop.Specification:F1500 plate-shell typeQty.:5 setsGas processing capacity:6500 Nm3/h·setGas inlet temp.:150~180oCGas outlet temp.:35-45oC9) Gas boosterFunction:deliver the clean cold gas to customer after boosting. Parameters:Q=27700m3/h P=13630Pa N=160KWQty.:2 sets(2 working, 1 standby)10) Air blowerFunction:supply the air for gasification of producer.Specification:9-26No5.6AParameters: Q=36189m3/h N=110KWQty.:2 sets,one for standby3. Water circulation in gas station1) Amount of cooling water in indirect cooler:100t/h Water temperature: tinlet=35oC toutlet=45oC2) Type selection of equipmentsSelect 3 sets of IS150-125-315 water pumps, one for standby.Parameters: Q=200m3/h H=32m N=30KWPart 6 Service, Construction and Quality AssuranceA. Service commitment1) Seller commits that the materials of contract goods, process, performance and other aspects will accord with the indexes of each item stipulated in the contract, and guarantee that the goods could be in normal service after installation and commissioning.2) After the acceptance from Buyer, the quality guarantee period is one year. (Except wearing parts).3) Within the quality guarantee period, Seller's engineer shall give a written response within 2 hours after receiving notes if the equipment has faults. If needs Seller go to site to solve the problem, the Seller shall go to site to make the site service at fastest speed by the most convenient transportation. If the operation of Buyer's personnel doesn't accord with the relevant technical requirements in 'Operation Instruction' of gas producer provided by Seller which will cause the damage or adjustment of gas producer and its auxiliary equipment, Buyer shall pay the costs for travelling, board and lodging on his own account; otherwise Seller shall pay the above costs.4) Seller shall guarantee to conduct lifelong service for contract goods.B. Project quality and safety guarantee measures1) Project quality assurance measures1.1 Quality assurance for components manufactured in the factory and purchased parts:1.1.1 During the manufacturing of components made in factory, the shift leader, designers, and responsible person for the in-plant quality of the project group will together make the supervision and inspection in various stages. After the manufacture is completed, the inspector dispatched by the company will go to make an overall test and inspection. Issue the certificate if the products are qualified, and then leave the factory. The equipments without certificate shall be resolutely prohibited to enter the construction site.1.1.2 For purchased parts, the products from the manufactures with a strict quality control system will be selected as a priority. The purchased parts entering the plant must have complete certificates. The purchasing staff shall be seriously responsible for the project group, and the related responsible person for quality from the project group have the right to question the quality and performance of purchased parts or ask to make the replacement.1.2 Guarantee for non-standard manufactured parts on site and installation quality:1.2.1 Materials quality control:The applied materials, welding rods and so on which are purchased at the site must have qualified certificates and material inspection list, so as to ensure the quality of whole the materials.1.2.2 The quality responsible person on site and head of the installation team will be overall responsible for the non-standard components and installation quality. Carry out strict supervision and inspection regularly according to relevant national codes. Make a final system test strictly to ensure the installation quality of the whole project.2) Safety guarantee measures:One special safety inspector will be set for the whole project. The safety inspector appointed for this project shall be with abundant construction experience on gas, good safety awareness and sense of responsibility.Equip with appropriate quantity of fire extinguishers on construction site. The safety inspector will be responsible for the arrangement and checking of fire extinguishers.3) Safety guarantee for hot-state operation and gas deliveryThe hot test only can be done after the pressure test, leakage test and cold test is completed for the whole system, and no potential safety hazard for the system itself is confirmed. The process of gas delivery under hot state shall be strictly carried out according to operation instruction and safety code, the whole process shall be done under the supervision of safety inspector. Company ProfileCompany ProfileVisionWith dees of rapid development and accumulation, China has been perfect and mature on technology and management in various industrial areas, shaping a complete processing manufacturing industry with competitive price, well known for its excellent skill, high efficiency and hardworking team with qualification for personnel dispatching.At the time of economic globalization, it is our consistent target and objective to integrate and export all kinds of technology, management mode, engineering project and manpower as per the actual requirement of our client With our own abundant technical strength, superior integration capability of technology and resources, well experienced of project implementation and management as basis and platform;Let China go out to the world, and make the world know of China;ProfessionalProfessional technical and management team with abundant experience in the implementation of domestic and international projects;ResponsiveResponsively and meticulously, translating your needs into complete solutions;IntegrationIntegrating various technologies and resources in China and fulfilling complementary advantages, by relying on professional teams;MotivationMotivated to provide the optimal solution and quality products;ExceptionalExceptional, delivery and,implementation of projects to meet, your expectations;Our TeamProfessional technical teamPrime is staffed with professional import & export team skilled with the practice of import and export business, including sea freight packing, logistics organization, L/C review, cargo booking, and customs clearance, L/C negotiation, double authentication of shipment documents, etc.All above personnel are well experienced in the execution of projects in Southeast Asia and Middle East. Complete procurement mechanismOur professional team of procurement offers strict management of supplier 's qualification inspection and selection, complete system of supplier listing, rating and elimination, to ensure the supplier is qualified and capable of implementing the project and supplied with product of high quality, and maintain a healthy and good condition of credibility, contract settlement and capital flow management.Quality management systemOur complete quality management system , the process control covering from Scheme formulation , engineering technology, detailed design, to processing and manufacturing of equipment and material , ex-factory test and site erection and commissioning till it put into production, which through multi-level inspection, tour inspection, supervision and node control can ensure quality of the final product.Well experiencedExecutive team is abundant in experience of overseas project implementation with similar project working experiences, esp. experience in Southeast Asia, Middle East projects; ISO System Certification Partners

× More Keyword ..

× More Menu ..

×

Manufacturing & Processing Machinery

×

Industrial Equipment & Components

×

Tools & Hardware Products