IPDB › China Industry › Industrial Equipment & Components
China, Chinese A10vso Series Hydraulic Pumps Best Supplier for Rexroth Piston Pump A10vso18, A10vso28, A10vso45, A10vso60, A10vso85, A10vso100, A10vso1401 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
Pump Vacuum EquipmentPiston PumpA10vso28A10vso45A10vso60A10vso85A10vso100A10vso140A10vso18 Hydraulic Piston PumpA10vso28 Hydraulic Piston Pump
Hangzhou PinXin Hydraulic Technology Co., Ltd.
Preview:
Product Description Type codeType code01 02 03 04 05 06 07 08 09 10 11 12 13 A10V(S)O /31 -V Version 18 28 45 71 88 100 14001Standard version (without code) High-speed version (external dimensions are the same as the standard version)-- - H Axial piston unit02Swashplate design, variable, nominal pressure 280 bar, maximum pressure 350 bar ------A10VS - A10V Operating mode03Pump, open circuitO Size (NG)04Geometric displacement, see table of values on pages 6 and 71828457188100140 Control device05Two-point control, direct operated DG Pressure controller hydraulic DR with flow controller hydraulicX-T open DFR X-T plugged with flushing function DFR1 X-T plugged without flushing function DRSC with flow and differential pressure control, electrically variable EF1) with pressure cut-offhydraulic remote controlled DRG electrical negative controlU = 12 V ED71 U = 24 V ED72 electrical positive controlU = 12 V ER71 U = 24 V ER72 Pressure-flow power control- DFLR Series06Series 3, index 131 Direction of rotation07Viewed on drive shaftclockwiseR counter-clockwiseL Sealing material08FKM (fluoroelastomer)V Drive shaft 18 28 45 71 88 100 14009Splined shaft ANSI B92.1astandard shaft S similar to shaft "S" however for higher input torque --R reduced diameter, limited suitability for through drive (see table of values, page 9) ○U same as "U", higher torque; limited suitability for through drive (see table of values, page 9)- W Mounting flange10ISO 3019-1 (SAE)2-hole C 4-hole------ D 1) See data sheet 92709 Type code01 02 03 04 05 06 07 08 09 10 11 12 13 A10V(S)O /31 -V Working port 18 28 45 71 88 100 14011SAE flange ports according to J518Working portsmetricFastening threadmetric; rearnot for through drive- -- 11 --- --41 Fastening threadmetric; lateral top bottomfor through drive -- 12 --- --42 SAE flange ports according to J518Working portsUNFFastening threadUNF; rearnot for through drive- -- 61 --- --91 Fastening threadUNF; lateral top bottomfor through drive -- 62 --- --92 Through drive (for mounting options, see page 53)12Flange ISO 3019-1 Hub for splined shaft2)Diameter Diameter18 28 45 71 88 100 140 without through drive N00 82-2 (A)5/8 in 9T 16/32DP K01 3/4 in 11T 16/32DP K52 101-2 (B)7/8 in 13T 16/32DP- K68 1 in 15T 16/32DP-- K04 127-2 (C)1 1/4 in 14T 12/24DP--- K07 1 1/2 in 17T 12/24DP----- K24 152-4 (D) 1 3/4 in 13T 8/16DP------ K174) Connectors for solenoids3)13Without connector (without solenoid, with hydraulic control only, without code) DEUTSCH - molded connector, 2-pin, without suppressor diode P = Available ○ = On request - = Not availableNotice Note the project planning notes on page 59. In addition to the type code, please specify the rel- evant technical data when placing your order. Hydraulic fluidsHydraulic fluidsThe A10V(S)O variable pump is designed for operation with HLP mineral oil according to DIN 51524.Application instructions and requirements for hydraulic fluids should be taken from the following data sheets before the start of project planning: 90220: Hydraulic fluids based on mineral oils and related hydrocarbons 90221: Environmentally acceptable hydraulic fluids 90222: HFD hydraulic fluids (for permissible technicaldata, see data sheet 90225)Notes on selection of hydraulic fluidThe hydraulic fluid should be selected such that the operat- ing viscosity in the operating temperature range is within the optimum range (νopt see selection diagram).NoticeAt no point of the component may the temperature be higher than 115 °C. The temperature difference specified in the table is to be taken into account when determining the viscosity in the bearing.If the above conditions cannot be maintained due to extreme operating parameters, please contact the respon-sible member of staff at Bosch Rexroth.Viscosity and temperature of hydraulic fluidsViscosityTemperatureComment Cold start νmax ≤ 1600 mm2/sθSt ≥ -40 °Ct ≤ 1 min, without load (p ≤ 30 bar), n ≤ 1000 rpm Permissible temperature differenceΔT ≤ 25 Kbetween axial piston unit and hydraulic fluid Warm-up phase ν < 1600 to 400 mm2/sθ = -40 °C to -25 °CNote the detailed information on operation with low tempera- tures, see data sheet 90300-03-B Continuous operation ν = 400 to 10 mm2/s this corresponds, for VG 46 for example, to a temperature range of +5 °C to +85 °C (see selection diagram) θ = -25 °C to +110 °Cmeasured at port L, L1observe the permissible temperature range of the shaft seal (ΔT = approx. 5 K between the bearing/shaft seal and port L, L1) νopt = 36 to 16 mm2/s Range of optimum operating viscosity and efficiency Short-term operation νmin 7 mm2/s t < 1 min, p < 0.3 ? pnom Selection diagram Maximum permissible viscosity for cold start16001000600Warm-up phase Minimum permissible viscosity for short-term operation7-40-25-10 0 1030 5070 90115 Temperature θ [°C] X-T plugged without flushing function Filtration of the hydraulic fluidFiner filtration improves the cleanliness level of the hydrau- lic fluid, which increases the service life of the axial piston unit.A cleanliness level of at least 20/18/15 is to be maintained according to ISO 4406.At very high hydraulic fluid temperatures (90 °C to maxi- mum 115 °C), cleanliness level 19/17/14 according to at least ISO 4406 is necessary.Please contact us if the above classes cannot be observed.Our advantages:1. We are doing stock trad over 10 years , shipping more faster with good price 2. We are professional supplier of hydraulics motor and pump also spare parts .3. Our factory is more than 10 years exprience production hydraulic motor pumps factory .4. we also dealer brand such as Rexroth DANFOSS Eton . Conpany introduction:We are a professional supplier of A2FM, A2FO, A6VE, A6VM, A7VO, A8VO, A10VSO, A4VG, A10VG series hydraulics for more than 10 years. There are many products available in stock. If you are going to purchare other brands hydraulics, we have Chinese brands for your consideration.Workshop show:Field of application:We are offer thiese machines We are offer these Brand Package:Delivery:Delivery time:We have huge quantity of inventory for complete pumps, motor and some spare parts, so the leading time is within 3days if have in stock. If haven't, within 5days if the quantity is less than 50pcs. It depends on the quantity ordered.Min. Order:If the model is common or the production in our stock warehouse, there is No MOQ for stocking production.Larger quantity, price will be more favorable.Deliever Way:By courier, like the DHL, UPS, Fedex,etc. It's door to door or barn to the door,usually 5-7 days to arrive.By air to air port, usually 3-5 days to arriveBy sea to sea port, usually 20-30 days to arrive.If your deliever time is very urgent, we suggest that you choose by courier or air.If not, it's very cheap to by sea.
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...