IPDB › China Industry › Instruments & Meters
China, Chinese Type 9stn, Immersion Heaters with 182mm X 130mm X 224mm Aluminum and Plastic Enclosure1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
HeatingRefrigeration Temperature ControlHeating ElementImmersion Heaters with 182mm X 130mm X 224mm Aluminum and Plastic EnclosureHeaterWater Heater
JPCI Controls (Foshan Gaoming) Co.,Ltd
Preview:
Product Description Immersion heaters with 182mm x 130mm x 224mm aluminum and plastic enclosure, or full aluminum enclosure, with 80mm offset. Fittings from 2" to M77x2. With mechanical thermostat. With or without manual reset thermostat. Power up to 21kW with built-in power relay. Heating elements dia. 10 and 12 mm.Type 9STN Main applications: Industrial liquid heating, hot water circuits, containers and buffer tanks.These heaters with aluminum enclosure are designed for industrial applications of medium power in three-phase, which require the use of contactor. They can receive one power relay, 3 poles 32A resistive. They exist only with thermostat temperature control. The enclosure lid may be transparent polycarbonate or aluminum. They are equipped with a device that allows adjusting the enclosure position after tightening of the fitting.The enclosure has a 80mm offset to go throw thick thermal insulation.They can be made in:-6 standard power levels: 6kW; 9kW; 12kW; 15kW; 18 kW; 21kW.-3 types of standard fittings with dia. 10 mm heating elements: : 2",2"1/2 and M77x2 -2 types of standard fittings with dia. 12mm heating elements: 2"1/2; M77x2-2 types of surface load density: 5W/cm2 and 10W/cm2. See technical introduction to optimize the surface load. Heater tube material: 3 heating elements, dia.10mm or 12mm, AISI 304 or Incolloy 800 (AISI 316; AISI 321; Incolloy 825 on request). Fitting material: brass, swiveling on housing, brazed on tubes. Supplied without gasket and without nut. See accessories below. Thread: - Dia. 10 mm heating elements: 2",2"1/2 and M77x2 - Dia. 12mm heating elements: 2"1/2; M77x2 Temperature control: Mechanical thermostat, temperature range 30-90°C (85-195°F). Other ranges available) Enclosure: Extremely robust,die-cast aluminum, 3mm wall thickness. Silicone foam gasket. Stainless steel cover screws with locking nuts. Gray epoxy paint RAL7035. Protected against galvanic corrosion. Designed for outdoor installation, IP65 and IK10. It also includes: - A fuse to protect internal circuits - An illuminated on- off switch -A pilot light for power supply and a pilot light for power output. There is 2 models of cover: - A PA66 cover with a polycarbonate transparent window allowing access to the settings. This window can be secured with seals. This case also includes a separate lid, with independent seals, providing access to electrical connections. In models with failsafe manual reset limiter, reset can be accessed after opening the window. -An aluminum cover. This model provides access to settings only after removing the cover. It is convenient for industrial applications that do not request frequent changes in settings. Cable glands:One M25, PA66, and one more hole for M25, closed by a plastic cap. Thermowell: in standard two thermowells in AISI304, dia.8 x 7 mm, 350mmlength. Electric connections: Built-in terminal block, with 6 terminals 10mm2 and 2 terminals 2.5mm2. This terminal block is provided with a strap between terminals 1 and 2. By removing this strap, it is possible to connect an additional safety device, a remote control, or a timer. Support grid: 1 grid AISI 304 for lengths from 400 to 600mm, 2 grids above. Not heating immersed zone: 50mm. Surface load: Standard 5 W/cm2 or 10 W/cm2, others values on request. Voltage:380-400V, three phases with neutral only. Standard options: Plastic cover with transparent polycarbonate window Aluminum cover Variants on request: -4-40°C (40-105°F) adjustable thermostat, manual reset at 60°C (140°F). -0-60°C (32-140°F), adjustable thermostat, manual reset at 80°C (176°F). -30-110°C (85-230°F) adjustable thermostat, manual reset at 130°C (266°F). -Thermal cut out inside a thermowell.It is also possible to produce models with digital electronic control. Ask our commercial department. Main references with transparent polycarbonate window* 5W/cm2; 2"1/2**brass fitting, without manual reset thermostat. Heating element diameterDia. 10 mm heating elementsDia. 12 mm heating elementsPower6kW9kW12kW15kWLength (mm)66098011001350AISI 304 Reference9STND7QV060C16609STND7QV090C19809STND7QV120C2K009STND7QV150C2O50Incolloy 800 reference9STND7QV060CL6609STND7QV090CL9809STND7QV120CMK009STND7QV150CMO50 10W/cm2, 2"1/2** brass fitting, without manual reset thermostat. Heating element diameterDia. 10 mm heating elementsDia. 12 mm heating elementsPower6kW9kW12kW15kW18kW21kWLength (mm)350500650680810950AISI 304 Reference9STND7QV060C13509STND7QV090C15009STND7QV120C16509STND7QV150C26809STND7QV180C28109STND7QV210C2950Incolloy 800 reference9STND7QV060CL3509STND7QV090CL5009STND7QV120CL6509STND7QV150CM6809STND7QV180CM8109STND7QV210CM950 5W/cm2, 2"1/2* brass fitting, with manual reset thermostat set at 100°C (212°F)** Heating element diameter Dia. 10 mm heating elementsDia. 12 mm heating elementsPower 6kW9kW12kW15kWLength (mm)66098011001350AISI 304 Reference 9STND7QV060C166N9STND7QV090C198N9STND7QV120C2K0N9STND7QV150C2O5NIncolloy 800 reference9STND7QV060CL66N9STND7QV090CL98N9STND7QV120CMK009STND7QV150CMO5N 10W/cm2, 2"1/2* brass fitting, with manual reset thermostat set at 100°C (212°F)** Heating element diameter Dia. 10 mm heating elementsDia. 12 mm heating elementsPower 6kW9kW12kW15kW18kW21kWLength (mm) 350500650680810950AISI 304 Reference 9STND7QV060C135N9STND7QV090C150N9STND7QV120C165N9STND7QV150C268N9STND7QV180C281N9STND7QV210C295NIncolloy 800 reference9STND7QV060CL35N9STND7QV090CL50N9STND7QV120CL65N9STND7QV150CM68N9STND7QV180CM81N9STND7QV210CM95N* For plain aluminum cover, replace T9D by T9G in the reference** 2" brass fitting instead of 2"1/2, replace D7 by D6 in the reference. (Only possible on dia. 10mm heating elements)M77x2 brass fitting instead of 2"1/2, replace D7 by D8 in the reference. (Possible on dia. 10mm and dia. 12mm heating elements)*** Manual reset thermostat set at 60°C, 80°C, 110°C, 130°C. (140°F, 176°F, 230°F, 266°F), replace the last character N by E, J, Q, U
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...