IPDB › China Industry › Industrial Equipment & Components
China, Chinese Yb-E Series 50V High-Performance Vane Pumps Low Noise & Ultra-Low Pulse for Precision Hydraulic Systems 252, 316, 3501 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
Pump Vacuum EquipmentVane Pump316350Vane PumpsPump
Tianjin Henghua Pipeline Technology Co., Ltd.
Preview:
Product Description YB-E series vane pumps with high-performance are featured by advanced performance,reasonable structure, good creditability, lower noise, ultra-low pulse and stable quality.Precisely made, the products can be used in the equipment with high precision, and are widely used in cutting, plastic, forging and engineering machinery fields and so forth.Specifications SeriesDisplacement of shaft end pumpDisplacement of cover end pump32V80, 100, 12540, 50, 63Installation and Use 1. In installation, the tolerance of concentricity between shaft of pump and motor must be less than 0.10mm(TIR) and the maximum permissible angle error is less than 0.2 degrees by using the flexible coupling; The pump shaft shall not bear the radial and axial load; The carrier must be firm with good rigidity and can fully absorb vibrations.2. If a pump is used at speed below 1200r/min, install the pump with the suction port upside so that the pump can suck up fluid easily at starting.3.Fix pipes, especially inlet pipes in accordance with the size of port and assemble safety relief valves in the system; The regulating pressure of the safety valve shall not be greater than the maximum pressure of the pump; Inlet pipes must be strictly sealed with no leakage; The fuel tank shall be equipped with a diaphragm to separate the bubbles and dirt from the oil; The oil return nozzle should be lower the fluid surface, the minimum depth of 50mm, even in a low, too, when the permissible level of to avoid the formation of bubbles 0.4. Oil should be kept clean, pipes and tanks must be thoroughly cleaned; Precise filters should be assembled with the advised precision of 25μm in the system, the cleanness level of oil should be withinNSA12.Fix the sufficient-volume filter (the rated flow rate should be greater than twice the pump flow) at the inlet of the pump 50mm above the bottom of the tank, with the suggested precision of 100pm(150 mesh).5. Selection of hydraulic oil : This series pumps are applicable to various oil liquids, including petroleum series oil, Water-cut hydraulic fluid, synthetic hydraulic fluid etc.However, the specifications of the pumps such as maximum pressure and maximum pump speed may be changed according to the type of hydraulic fluids to be used. For details, please refer to the specifications of the pump concerned. To improve the pump performance, prolong service life, it is recommended to use anti-wear hydraulic oil (such as ISO VG32 or ISO VG46).When the oil viscosity 30 cSt is the best (to keep the temperature within 10 ~60oC , the best is 35~50oC ), especially to avoid high temperature continuous operation, otherwise the pump will shorten the service life, set the heater and cooler when necessary to adjust the oil temperature.6. Check the inlet , outlet and direction of rotation before starting the pump. Turn the shaft of pump evenly and nimbly by hand after fixing the pump. It is best to fill the pump with oil for the first time. At an initial operation or at an operation after a long rest, the pump may have difficulty in sucking up fluid; In such cases, an air bleed valve should be installed beforehand on the discharge side or discharge air by slightly slackening the connection on the discharge side. At starting, operate the pump intermittently as far as possible with no load.7. At startup, If the oil viscosity is higher than the suitable viscosity (46cSt), the pressure should be limited to50% or less of their respective rated values until the system has warmed up.Comprehensive Product List for Hydraulic Power SystemsCategoryProduct NameDescription / Key TypesPower Source Hydraulic PumpsGear Pumps, Vane Pumps, Piston Pumps (Axial & Radial), Variable Displacement PumpsPower Units (Power Packs)Custom-built reservoirs, with pump, motor, valves, filters, and coolers integrated.Actuation Hydraulic CylindersTie-Rod Cylinders, Welded Body Cylinders, Telescopic Cylinders, Double-Acting, Single-ActingHydraulic MotorsGear Motors, Vane Motors, Piston Motors, High-Torque Low-Speed (HTLS) MotorsControl Hydraulic ValvesDirectional Control Valves: Solenoid, Proportional, Manual; Pressure Control Valves: Relief, Reducing, Sequence; Flow Control Valves: Check, ThrottleProportional & Servo ValvesHigh-precision electro-hydraulic valves for closed-loop motion control.Fluid Conditioning Reservoirs (Tanks)Steel or stainless steel tanks with baffles, air breathers, and level indicators.Hydraulic FiltersSuction Filters, Pressure Filters, Return Line Filters, Off-Line Filtration UnitsHydraulic Oil CoolersAir-Blown Oil Coolers (with fan), Water-Cooled Oil Coolers, Shell and Tube, Plate Heat ExchangersHeat Exchangers Transmission Hydraulic Hose & AssembliesHigh-Pressure Hose, Spiral Wire Hose, thermoplastic hose with reusable or permanent fittings.Steel Tubing & PipeSeamless steel tubing for hydraulic lines.Quick Release CouplingsFlat-Face, Threaded, Ball-Lock couplers for fast, leak-free connection/disconnection.Accessories & Sealing AccumulatorsBladder, Piston, and Diaphragm types for energy storage, shock absorption, and leakage compensation.Sealing Kits & ComponentsO-Rings, Rod Seals, Piston Seals, Wear Rings, Gaskets, and Wipers.Pressure Gauges & SensorsAnalog gauges, digital pressure sensors, pressure transducers.Hydraulic Fittings & AdaptersElbows, Tees, Unions, Plugs, ORFS, JIC, NPT, BSPP, Metric fittings.Specialized Systems Steering Control UnitsOrbital Steering Units for agricultural, construction, and marine vehicles.Hydrostatic Transmissions (HST)Integrated pump and motor system for infinitely variable speed control.Optional additional for your company:Custom Solutions; Integrated Systems & Manifolds; Custom-designed hydraulic systems, valve manifolds, and test benches. Optional additional for your company: Custom Solutions; Integrated Systems & Manifolds; Custom-designed hydraulic systems,valve manifolds, and test benches.
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...