IPDB › China Industry › Instruments & Meters
China, Chinese Megger Dcm340 600A 600 V AC DC Clamp Multimeter1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
Meter for ElectricityMultimeterMeggerMegger Dcm340
Shenzhen HOBOY Instruments Co., Ltd.
Preview:
Product Description Product Parameters 600A a.c. And d.c. Clampmeter w/ V; Ohms And HzDC and AC current and voltage600 A and 600 VResistance and continuity31/2 digit, 4000 count display with backlightHigh resolution digital bar graphPeak, min/max and data-hold functionsDescriptionMegger DCM340 - 600A 600 V AC/DC Clamp Multimeter DC and AC current and voltage600 A and 600 VResistance and continuity31/2 digit, 4000 count display with backlightHigh resolution digital bar graphPeak, min/max and data-hold functionsThe Megger DCM340-EN digital clamp meter is an average-sensing multimeter for measuring current, voltage, resistance, and frequency in electrical testing applications. It has a clamp with two jaws that can close around an electrical conductor up to 1.3" (35 mm) in diameter to measure current without touching or interrupting the circuit. The meter comes with detachable test leads that measure voltage, resistance, and frequency. The peak + or - function records instantaneous peak positive or negative values for current and voltage.The maximum or minimum reading mode displays the highest or lowest reading in a session to track a sudden increase or decrease in readings. The relative zero mode stores a reading in memory to use as a zero point for subsequent readings, allowing quick comparison of multiple readings. An audible continuity sensor confirms that the circuit conducts electricity. The hold function keeps a reading on the display, even after the meter is disconnected.The meter's liquid crystal display (LCD) shows readings in digits and on a bar graph and is backlit to provide readability in low light. The unit automatically turns off after 30 minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced. A finger guard on the body of the meter helps protect fingers from shock. The meter can survive falls of up to 1.2 meters to a hardwood or concrete floor.This average-sensing, or average-responding, meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has a sinusoidal waveform. It has a 4,000-count resolution, meaning that it can display up to 3,999 units (3-3/4 digits) before the operating range needs to be changed. The meter meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category III installations up to 600V, which covers items used with enclosed building circuit installations (such as service panel parts, branch circuits, and fixed installations that are connected directly to a building's AC power supply). The unit comes with a pouch for transporting and storing the meter.The DCM340 is a highly versatile instrument and ideal for use in the installation, maintenance, monitoring or checking of a.c. or d.c. electrical systems and equipment.There are four instruments in the DCM series of clamp meters, including the 400 A a.c. current-only DCM310; the DCM320 which includes voltage and resistance measurement; the DCM330 Fork-Multimeter, which is an open fixed jaw design; and this, the DCM340. Capable of measuring a.c. and d.c. current up to 600 A; a.c. and d.c. voltage up to 600 V; resistance up to 400 Ω and frequency up to 400 Hz, the DCM340 is the most versatile in the range.Current measurement combined with the comprehensive and accurate multimeter functions of the DCM340 eliminate the need to carry around both a clamp meter and multimeter - this instrument does it all.The large clear digits of the numeric display are complemented by the high-resolution digital bar graph, useful for indicating trending and fluctuation of measurement. The backlight assists use in poorly lit areas such as distribution cupboards and corners of switchrooms; and the data-hold feature enables use on difficult access cables where otherwise the display may be impossible to see.Min/Max hold provides the ability to store the maximum and minimum d.c. or rms values over a period of time. While storage is taking place, either the present, maximum or minimum value can be displayed. Peak hold stores the maximum and minimum peak value of an a.c. signal at a 10 ms sample rate. The auto-off feature automatically places the meter in power-save mode after 30 minutes from power-on, but this can be disabled if required for min/max measurements.Using the Relative mode (REL), a stable value can be stored, the instrument zeroed at that point, and then any variation from that value is displayed as a direct measurement relative to it.The DCM340 is safety rated to IEC 61010-1 Cat III 600 V, and is drop-tested to 1.2 m onto a hard floor. It is supplied with test leads and a carry case, and a full 1-year manufacturer's warranty.ApplicationsThe DCM340 is designed to be used on electrical systems and equipment where there is a need to measure current, volts, resistance and frequency. It is therefore intended for use while installing, maintaining, fault-finding or monitoring those systems.The min/max and peak-hold enable maximum load currents from equipment to be identified such as start-up currents to motors and heaters.With the added benefit of d.c. current measurement, it can also be used in applications including domestic power generation from solar panels and wind-turbines; battery monitoring; automotive uses for charging and load circuits; electric vehicle servicing such as fork-lift trucks; lift maintenance; UPS commissioning, servicing and maintenance; electro-plating plants and welding equipment servicing.In The BoxBatteryPouchTest LeadsUser GuideManuals/GuidesBrochuresMegger Multimeters/Clampmeters - CatalogManualsMegger DCM340 User ManualOtherData SheetManufacturer SpecsAC currentRangeAccuracy 50 - 60HzAccuracy 61 - 400Hz0-60.0 A±1.9% ±7 digits±2.5% ±7 digits60.0 - 400.0 A±1.9% ±5 digits±2.5% ±5 digits400 - 600 A±2.5% ±5 digits±2.9% ±5 digits DC CurrentRangeAccuracy0 - 60.0A±1.5% ±10 digits60.0 - 400.0A±1.9% ±5 digits400 - 600 A±1.9% ±10 digits VoltageRangeAccuracy 50 - 500HzAccuracy DC0 - 400.0 V±1.0% ±5 digits±0.7% ±2 digits400 - 600 V±1.0% ±5 digits±0.7% ±2 digitsInput Impedance:1 MΩ // < 100pF Resistance and ContinuityRangeAccuracy0 - 400.0 Ω±1% ±3 digitsOpen circuit voltage3 VContinuity Checkbeeper sounds @ < 30 Ω FrequencyRangeResolutionAccuracy20 - 400 Hz1 Hz±0.1 % ±2 digtits SpecificationsSensitivity3 APeak Hold±3% ±15 digitsSample time10 msMIN/MAX Holdadd 15 digits to accuracy for a.c. & d.c. APositional error±1% of readingOverload protection600 V & 600 A rmsAC conversionAverage sensing rms indication calibrated to the rms value of a sine wave inputAuto power-off30 minutes after power-onLCDDisplay31/2 digit large-scale readoutCount40,000Sample Rate1.5 per secondOverrange"OL"Power Requirement 1 x 9V PP3 MN1604 6LR61 alkaline cellBattery life200 hours (alkaline)TemperatureOperating0°C - 30°C <80% Rh30°C - 40°C <75% Rh400°C - 50°C <45% RhStorage-20°C - +60°C (<81% Rh) (batteries removed)SafetyOvervoltage safety categoryIEC 61010-1 600V CAT IIIOperating Altitude2000 mDrop-protection1.2 m onto a hardwood surfaceJaw size/maximum conductor35 mm diameterCalibration period12 month recommended Dimensions68 mm (W) x 237 mm (H) x 42 mm (D)Weight225 g including batteriesTech SpecsClamp Meters/Clamp Meters TemplateTrue RMSYesMaximum Current AC400 AMaximum Voltage AC600 VMaximum Voltage DC600 VMaximum Conductor Size35 MM (1.38 IN)ResistanceYesCapacitanceNoAuto Ranging/ManualManualIn-Rush CurrentNoTest Equipment General AttributesWarranty3 YEARSSafety ApprovalCEProduct Weight225 GRAMS (0.496 LBS)Product Height42 MM (1.65 IN)Product Length68 MM (2.68 IN)Product Width237 MM (9.33 IN)Data LoggingNoHTS/Schedule B Number9030.31.0000ECCN NumberEAR99Calibration IncludedNonePower Supply VoltageBattery PoweredCountry of OriginTaiwanShipping Height3.00 INShipping Length13.15 INShipping Width6.90 IN Packaging & Shipping As an important international instrument sales platform, our company has the authorization qualifications of many international first-line brands. Relying on the advanced digital information management platform and international procurement platform, we provide more than 100,000 instruments, industrial MRO products, industrial products and spare parts to global customers. Our business scope: industrial testing, non-destructive testing, gas testing, electrical testing, laboratory testing, water quality testing, environmental testing, medical testing... So far, we have become an important partner of many global top 500 companies and well-known local Chinese companies. Create an efficient supply chain system to provide customers with strong supply guarantee.
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...