IPDB › China Industry › Industrial Equipment & Components
China, Chinese Stainless Steel Dehydration Pump and Dehydration Pump1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
Drying MachineVacuum Drying MachineNo BlockageSubmersible Sewage Pump
Liaoning Jinrong Machinery Import and Export Co, . Ltd
Preview:
Product Description Product DescriptionStainless steel dehydration pump:Introduction:The QW (WQ) type non clogging submersible sewage pump is a new generation of pump product developed by our company based on the introduction of advanced foreign technology and combined with the characteristics of domestic water pump usage. It has significant energy-saving effects, anti winding, non clogging, automatic installation, and automatic control. Compared with traditional impellers, the impeller of this pump adopts a single or double channel form, which has very good flow capacity. Coupled with a reasonable volute chamber, the pump has high efficiency. The impeller has undergone dynamic and static balance tests, making the pump operate without vibration. The WQK sewage pump with cutting device adopts the most advanced method and is designed with the most reasonable hydraulic characteristics, allowing the electric pump to operate at full head. It is the best combination of excellent dry motor and water pump. The JYWO series automatic mixing submersible sewage pump is a new environmentally friendly product developed using excellent water as a model. It has unique functions in discharging solid particles and long fiber garbage, as well as reducing sedimentation in sewage pits.Product ParametersBy adopting a unique single or dual time plate discharge wheel structure, the ability of dirt to pass through is greatly improved, which can effectively pass through 5 times the fiber material of the pump diameter and solid particles with a diameter of about 50% of the pump diameter.The mechanical seal uses a new type of hard and corrosion-resistant titanium tungsten material, which can ensure the safe and continuous operation of the pump for more than 8000 hours.The overall structure is compact, the volume is small, the noise is low, the energy-saving effect is significant, the maintenance is convenient, and there is no need to build a pump room to submerge in water, which greatly reduces the project cost.The pump is equipped with a high-precision anti-interference water leakage detection sensor in the sealed oil chamber, and a thermal sensor is embedded in the stator winding to automatically protect the water pump motor.A fully automatic control cabinet can be equipped according to user needs to automatically protect the pump from water leakage, leakage overload, and overheating, improving the safety and reliability of the product.The float switch can automatically control the start and stop of the pump according to the required liquid level changes, without the need for dedicated personnel to supervise and use it conveniently.A dual rail automatic coupling installation system can be equipped according to user needs, making installation and maintenance convenient and simple.There are two different installation methods, fixed automatic coupling installation system and mobile free installation system.WOK has a particularly strong ability to discharge pollutants and has good cutting performance. It can shred and discharge impurities such as long fibers, plastic paper, belts, cloth strips, straw, ropes, etc. in sewage.The JYWQ model utilizes the pump's own outlet pressure to stir and mix the sediment in the sewage tank, truly achieving the goal of completely discharging the sediment in the sewage tank.Purpose:1. It can pump clean water, sewage with particles, and corrosive media.2. Suitable for urban sewage treatment plant drainage systems, municipal engineering, construction sites, etc.3. Suitable for chemical, petroleum, pharmaceutical, paper industries, etc.4. Suitable for cement plants, steel mills, coal processing industries, etc.Usage conditions:1. The temperature of the medium shall not exceed 40 degrees Celsius, and the density of the medium shall be ≤ 1150kg/m3,2. The pH value is between 5-9.3. The altitude shall not exceed 1000 meters. The viscosity of the conveying medium shall not exceed 1000CP.4. The product must be completely submerged in water during operation, but the diving depth must not exceed 10m.Technical Specifications:Model: QW50-18-9-1.1P.Flow rate: 18m3/h.Lift: 9m.Power: 1.1KW.Material: Stainless steel 304.Ordinary motor single-phase 220V, 230V, 60HZ.Liquid medium: water.Export size: DN50.Precautions for use:1. Before use, a comprehensive inspection should be conducted on the electric pump for any damage during transportation and storage, such as whether the cables and plugs are intact, whether the bolts are loose, and whether oil has seeped out of the pump casing. If any damaged parts are found, they should be replaced and the pump should not be operated with "disease". The cold insulation resistance of the motor should be greater than 50 megohms, and leakage protection devices should be installed and reliably grounded.2. Next, check if the voltage fluctuation range is between+5% and -15% of the rated voltage (otherwise it may shorten the motor life or even burn out). If the electric pump is used far away from the power source, the transmission line should be appropriately thickened (the diameter of the power transmission line must be greater than that of the water pump power line, otherwise the power line will be too thin and cause the voltage to drop too much, making it impossible to start and operate). When the power supply voltage is too low (cannot be adjusted), if the pump submerges into the water and the power supply is turned on, if there is no water discharge or slow water discharge, it should be started with no load and put into the water for operation after normal operation. In addition, the connection of the power supply line should be strictly sealed and wrapped to prevent leakage due to water seepage3. Connect the power cord to idle for a few seconds (not exceeding. 60 seconds), check if the startup and operation are normal, and if the direction of rotation is correct (if the three-phase electric pump is not rotating correctly, connect any two of the power output lines). If there is no water output or insufficient water output after power on, the rotation is still incorrect, and connect the wiring.4. Connect the conveying pipe that matches the outlet, tie it tightly with a clamp, and string a rope at the handle for lifting. Do not hang the water pump with a cable. The water pump works in a lake, and the depth should not exceed 5 meters. It should be at least 50cm away from the bottom of the water. Cover it with a bamboo basket or wire mesh to prevent water from blocking the filter screen and preventing the pump from working properly.5. When the submersible pump is working, attention should be paid to the decrease in water level (especially when pumping well water). The pump should not be exposed to the water surface and should not be dehydrated for a long time to prevent the motor from heating up and burning out the stator winding.6. Please do not wash, swim or let livestock into the water near the working face to prevent accidents; Do not touch the water pump when it is wet and powered on.7. The electric pump must be used within the specified head range and cannot be used below 80% of the specified head, otherwise the electric pump may burn out the motor due to overload.Detailed Photos Company ProfileLiaoning Jinrong Machinery Import and Export Co., Ltd. is a company with its own import and export rights, and is a large group company integrating industry and trade. The registered capital of the company is RMB 180 million. The company includes metallurgical equipment manufacturing company, electric furnace equipment manufacturing company, electrical equipment manufacturing branch, mechanical processing branch and metallurgical design and research Institute.Our company can undertake all kinds of metallurgical equipment design, manufacturing, installation, commissioning, trial production turnkey project. Our company can provide mining machinery and equipment, ironmaking blast furnace, sintering machine, coke oven, converter, electric arc furnace, ladle refining furnace, continuous casting equipment, steel rolling furnace, steel rolling production line, steel structure plant and crane and other metallurgical equipment and metallurgical machinery. Various other types of mechanical equipment are also available.Our company is the direct agent of Anshan Steel, Bensteel, Fusteel and other large steel mills, the variety of steel is complete: pipe, plate, profile, wire and so on are in stock. If the special specifications, materials and other requirements, we can organize the order to purchase, schedule production and rolling, to ensure supply. Our company has a history of 30 years, and now has established friendly contacts with more than 120 countries and regions and carried out various aspects of cooperation. We welcome customers from all over the world to visit our company.Location :1-51-901-3041, Floor 9, Jiangsu Building, Qianyuan Emerging Market, Tiexi District, Anshan City, Liaoning ProvinceTotal Number of Staffs 585Total Number of Managers 40Total Number of Technical Staffs 160Total Number of QC Staffs 15Total Number of workers 310Total Number of other staffs 60Certifications
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...