IPDB › China Industry › Chemicals
China, Chinese Excellent Corrosion Resistance Epoxy Vinyl Copolymer Copolymer Ester Resin for Chemical Construction Materials Engineering Industry1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
Plastic PolymerPolymer ResinVinyl Ester ResinEpoxy Vinyl Copolymer Ester Resin
Changzhou Rule Composite Material Co., Ltd.
Preview:
Product Description Vinyl Ester Resin INV-V470Product DescriptionBrief introduction:INV-V470 is a novolac epoxy vinyl ester resin with the following characteristics:1. Moderate reactivity, suitable for hand lay-up, pultrusion, winding and other molding processes;2. Medium viscosity, good curing characteristics, high curing degree of products;3. High toughness, crack resistance, high heat resistance temperature, excellent strength retention rate at high temperature.Epoxy vinyl ester resin is prepared by the chemical reaction of epoxy resin and methacrylic acid through ring-opening addition. It retains the basic segment of epoxy resin, and has the good process performance of unsaturated polyester resin. After curing under suitable conditions, it shows some special excellent properties.Matters needing attention:1. The transportation shall comply with the regulations on the transportation and handling of hazardous chemicals in Chapter V of the State Council's "Regulations on the Safety Management of Chemical Hazardous Substances".2. The product should be stored in a cool place below 25oC, avoid fire and isolate the heat source.3. The shelf life is 3 months under the specified storage conditions.Features:The standard bisphenol A epoxy vinyl resin is a vinyl resin synthesized by the reaction of methacrylic acid and bisphenol A epoxy resin. It has been dissolved in styrene solution. The specific molecular structure is shown in the figure below.Product ParametersLiquid resin properties (25oC): ProjectINV-V470Testing methodAppearance (visual inspection)Light yellow transparent liquidGB/T 8237Viscosity (mPa.s)100-300GB/T 7193Acid value (mg KOH/g)4-20GB/T 7193Solid content63-69GB/T 719325oC gel time (min)*10-30GB/T 7193 *The curing agent uses AKZO M-50, the dosage is 2%, and the accelerator uses AKZO NL 49P (1% Co) 1%.Physical properties of resin castings: ProjectTest valueTesting methodTensile strength (MPa)70GB/T 2567Tensile Modulus (GPa)3.5GB/T 2567Elongation at break (%)2.0-4.0GB/T 2567Bending strength (MPa)140GB/T 2567Flexural Modulus (GPa)3.5GB/T 2567Impact toughness (KJ/m2)10.1GB/T 2567Heat distortion temperature (oC)145GB/T 1634Note: 1) the casting system sample method is implemented according to GB/T 8237;2) Post-curing treatment of the casting body: room temperature × 24 hours + 100 °C × 3 hours.Our AdvantagesRule Composite Material covers an area of 50, 000 square meters, with a modern office building, an independent R& D center and a high-standard production workshop, equipped with the leading DCS automatic control production device. We also have a strong and advanced quality control department and technical support laboratory. Recommended ProductsItem No.Gel Time(25oC)MinChemical CategoryFeaturesApplicationINV-V41110-17Bisphenol AExcellent construction technology; excellent corrosion resistance, good corrosion resistance to general acids, alkalis, salts and organic solvents; high solid content, excellent mechanical and mechanical propertiesChemical anti-corrosion equipment, engineering, sporting goods, transportation.INV-V411M8-18Bisphenol AStandard bisphenol A type epoxy vinyl ester resin. Excellent construction technology, excellent corrosion resistanceWidely used in chemical engineering of many chemical media such as acid, alkali, salt, organic solvent and pipes, tanks, towers, tanks, pools in industry.INV-V411W20-30Bisphenol AExcellent corrosion resistance, combined with performance and cost advantages, with better price/performance ratioAnticorrosion equipment and engineering in conventional chemical industry.INV-V411L- GXX30-120( can be customized)Bisphenol AHas lower viscosity, adjustable gel time, lower exothermic peakVacuum infusion molding process to prepare composite products, such as boats, wind power fieldsINV-V4168-14 High reactivity, heat resistance, excellent toughnessRapid pultrusion to prepare rods, cores, pipes and other productsINV-V44015-55 Low cure shrinkage, pre-acceleration, anti-sagPreparation of composite molds, or composite products with low shrinkage requirementsINV-V480----Mgo ThickeningHigh reactivity, thickening with magnesium oxideSMC molding process to prepare battery shells, fan impellers, etc.INV-V495----Mgo ThickeningHigh toughness, magnesia thickenerUsed together with low shrinkage agent, it can prepare products with low shrinkage, high strength, high toughness, high heat resistance and heat aging resistance, etc. It is suitable for BMC, SMC, prepreg and other molded products. e.g. composite toe caps, helmets.INV-V65030-60(can be adjusted based on the accelerator content)Halogen Free Flame RetardantHalogen-free, in addition to the corrosion resistance of conventional epoxy vinyl ester resins, it also has good flame retardancy. It is an integrated solution product with anti-corrosion and flame retardant properties.Mainly used in corrosion-resistant equipment with flame retardant requirements, such as wet electrostatic precipitators in thermal power plants, chimneys, etc.INV-V47010-30Phenolic AldehydePhenolic modified epoxy vinyl ester resin, high crosslinking density, HDT=145 oC, has more excellent heat resistance and corrosion resistance; especially in acid oxidizing environment, it has long-term resistance.Heavy-duty anti-corrosion fields with strong corrosiveness and high temperature in chemical engineering and industry. CertificationsPackaging & Shipping FAQ1. How can I get a sample?Small quality of sample in stock will be free, but the freight will be charged.2. Are you able to adjust the formula to meet our requirement?We have our own technical department, after you test the sample, please tell us your detailed requests, we are able to adjust the resin according to your requests, and bring better properties to your finished products.3. What is the lead time for mass production?Honestly, it depends on the quantity. We will try our best to make the production plan according to your ETA.4. What is your terms of payment?100% full payment for the 1st trial order; from next order, 30% payment in advance, 70% payment after buyer get the B/L copy. We also accept L/C if you need.
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...