IPDB › China Industry › Chemicals

China, Chinese Dust-Proof Anti Slip Polyurethane Coating for Bridge Deck¹ Industrial Products Supplier Manufacturer Details, price list catalog:

China Industrial Products Supplier Manufacturer List Catalog

Paint Coating Building Coating Epoxy Floor Paint Coating Paint

Jiangsu Shuocheng New Materials Technology Co., Ltd.

Preview:

Product Description Coating process requirements1. The coating operation should be carried out under the environmental conditions of 5~35oC and relative humidity below 80%, and the surface temperature of the substrate should be higher than the dew point temperature by more than 3oC.2. Before coating, the surface of the substrate should be dusted and cleaned; the paint should be stirred evenly before spraying. When coating, airless (air) spraying, rolling, brushing and other methods can be used. In order to obtain better coating quality, high-pressure airless spraying is recommended.For edges, corners, cuts and other parts, a layer of paint should usually be sprayed first, and then fully coated according to process requirements.3. The coating film thickness should be strictly controlled to ensure that 90% of the measured points reach the specified thickness. For the measured points that do not reach the film thickness, the film should reach more than 90% of the specified value.4. According to different coating forms, if necessary, an appropriate amount of deionized water/tap water can be added to dilute and adjust the paint viscosity for coating, but the amount added shall not exceed 10% of the coating amount.5. When applying composite coating (primer plus topcoat), first check whether the primer is completely dry. Topcoat can only be applied after the primer is completely dry (or according to the primer matching requirements); during the coating interval, the surface must be clean, dry and free of pollutants; if the primer and topcoat are products of different manufacturers, a matching test should be done first, and construction can only be carried out after confirming that they are qualified and there are no problems;6. When the designed film thickness is high, the designed film thickness can be achieved through multiple layers of construction; when multiple layers are applied, pay more attention to the state of the paint film coating.The second layer of coating must be applied after the previous layer is completely dry. The surface drying time of one coat at room temperature is 0.5-2 hours.7. The paint film coating should be protected within 96 hours after spraying to avoid contact with any water (liquid substances) to avoid affecting the coating quality.8. Since this product is a two-component product, the paint should be mixed according to the actual usage demand. The prepared working paint must be used up within 2 hours in summer and within 4 hours in winter. If the paint exceeds the applicable period, the viscosity of the paint will increase, gelling until it is completely solidified. In this case, even if the paint is applied forcefully, the physical properties such as adhesion and corrosion resistance will be affected. Therefore, we recommend that the amount of paint be appropriately mixed according to the production situation.Coating performance test conditions1. Product performance test (based on the actual dry paint film coating);2. General basic performance: gloss, test after actual dry; hardness impact resistance, bending flexibility and adhesion test, after actual dry, it should be placed in a constant temperature and humidity chamber (temperature 23±2oC/humidity 50±5%) for at least 24 hours before testing;3. Initial test: Water resistance test: dripping test 4 hours after paint film spraying;4. Long-term test: neutral salt spray resistance and water resistance test: the paint film coating is cured for 7 days after actual dryness, and it needs to be placed in a constant temperature and humidity chamber (temperature 23±2oC/humidity 50±5%) for at least 16 hours before testing;Storage and transportation1. It must be stored in accordance with national regulations; the storage environment should be dry, cool, well ventilated, prevent direct sunlight, and stay away from heat and fire sources. The packaging container must be kept sealed; handle carefully; the effective storage period is 6 months from the date of production. After the storage period, it must be inspected and qualified before use.2. During transportation, the product should avoid being squeezed, and should be protected from severe cold, rain, sun exposure and other harsh environments, and should comply with the relevant regulations of the transportation department.Health and Safety1. Please read the safety notices and product instructions on the container packaging in detail. Use under well-ventilated conditions. When spraying, you must protect your respiratory organs from damage by the spray, avoid inhaling paint mist, and avoid contact between skin and eyes and this type of product. It is best to wear a ventilated mask, safety goggles and protective gloves; if accidentally splashed on the skin, rinse immediately with appropriate detergent, soap and water. If accidentally enters the eyes, rinse thoroughly with water and seek medical treatment immediately.2. The construction site must be well ventilated. When constructing in narrow or airless places, strong ventilation must be provided.3. The construction site must be equipped with certain fire prevention and firefighting equipment.4. This product should not flow into the sewage system.5. For detailed safety measures, see the Material Safety Data Sheet (MSDS) of this product; in addition, the safety regulations stipulated by the relevant country or local government should be observed.Color differenceThis product is mainly used as a topcoat. The color may vary slightly from batch to batch. It may fade, turn white, and powder after being weathered under direct exposure to sunlight and weathering for a period of time beyond the product protection period.Disclaimer1. The information provided in this manual is entirely based on our understanding in the laboratory and practice. Shuocheng's products are considered semi-finished products. The use of such products is usually beyond our control. Therefore, Shuocheng only guarantees the quality of the product itself. In order to adapt to local regulations, the product may be adjusted appropriately. We reserve the right to modify the manual without further notice.2. For your own needs and specific applications, please consult our service department: 0516-83316660 to obtain specific guidance on the applicable performance of the relevant products.Product ParametersProduct DescriptionThis product is a water-based two-component self-drying product, made of water-based aliphatic acrylic polyurethane resin, HDI as curing agent, and added with environmentally friendly pigments, fillers, functional additives and other materials; it has the characteristics of strong adhesion, high hardness, good anti-corrosion effect, safety and environmental protection.Product FeaturesThe coating film is plump and dense, with good substrate adhesion, bright color, high gloss and hardness, good flexibility, and good weather resistance; it has good mechanical strength and decorative properties; it is easy to operate and construct.Application FieldIt is suitable for topcoat coating with high requirements for surface decoration and weather resistance. It can be widely used as surface decoration of metal substrates such as steel structures, wind power towers, mechanical equipment, and engineering machinery; it is usually used with epoxy anti-corrosion primers, and can also be used with epoxy micaceous iron intermediate paints; this product has a high gloss, and when used with primers, it has better performance, and has both decorative and high anti-corrosion and weather resistance. It can be used with water-based epoxy anti-rust primers, epoxy micaceous iron intermediate paints, water-based acrylic paints, and water-based epoxy ester paints.SC-HP4105Water-based two-component acrylic polyurethane topcoatPackaging specificationsComponent A: Water-based two-component acrylic polyurethane topcoat 20kg/barrelComponent B: Curing agent 2kg/barrelItemTest/StandardDescriptionColor/CodeGB11186Medium GrayAppearanceVisual InspectionSmooth and FullFineness/umGB/T 6753≤25Solid Content/%GB/T 1725>42Density/g/mlGB/T 67501.25±0.1Gloss (60° GU)GB/T 975475±5°Adhesion (Cross-Cut Test)/GradeGB/T 9286≤1Impact Resistance/kg·cmGB/T 1732≥50Pencil Hardness/GradeGB/T 6739≥HBTheoretical Coverage30-40um (based on dry film thickness)8-6m2/kgNote: The data listed is based on factory batch production products, and there will be slight changes due to different colors and batches.Construction condition parametersPaint mixing ratio (mass ratio): A: B = 10: 1Component A: Main paintComponent B: Curing agentDiluent: Deionized water/clean tap waterMaturation period: 3-5minActivation period: 4.0h (10±2oC) / 2.0h (25±2oC)Note: All data are valid only for mixed paint.Construction technologyConstruction technology Construction method: Thinner ratioSpraying Use airless spray or air spray with a cross-cross method. 0-10%Brush/roller Apply with a brush/roller with a cross-cross method. 0-5%Spraying methodSpraying type Spray gun diameter Spraying pressure Spray gun distance Spray fan widthAirless spray: 0.017-0.025inch 15-25Mpa 30-40cm 25-50cmAir spray: 2.0-3.0mm 0.4-0.6Mpa 20-30cm 15-25cmDrying and curing timeBaking (actual drying): 80oC/100minNatural dryingTemperature 5oC 15oC 25oC 35oCSurface (touch) dry 100min 80min 60min 45minActual drying (trampling) 40h 36h 30h 24hRe-coat after drying 6h 4h 3h 2hDry to cure 10d 8d 7d 4dNote: 1. The above drying and recoating data are based on the paint (dry) film of 35±5um, relative humidity ≤60%, and natural drying conditions;2. Surface (touch) dry: no fingerprint residue or no adhesion when lightly pressed with fingers.3. Actual drying (trampling): the shortest time that the coating can allow normal walking without leaving permanent footprints, marks or other physical damage.4. The determination of drying and curing time is based on temperature and relative humidity, relative humidity ≤80%, and dry film thickness is within the average dry film thickness range.5. Recoating after drying, shortest interval: the recommended shortest time interval for the construction of the next coating.6. Dry to solid and usable: the shortest time that the coating can be permanently exposed to a specific environment/medium.Tool cleaning: deionized water/clean tap waterSC-HP4205Water-based two-component acrylic polyurethane topcoatPackaging specificationsComponent A: Water-based two-component acrylic polyurethane topcoat 18kg/barrelComponent B: Curing agent 3kg/barrelProduct parametersItemTest/StandardDescriptionColor/CodeGB11186Medium GrayAppearanceVisual InspectionSmooth and FullFineness/umGB/T 6753≤25Solid Content/%GB/T 1725>42Density/g/mlGB/T 67501.25±0.1Gloss (60° GU)GB/T 975485±5°Adhesion (Cross-Cut Test)/GradeGB/T 9286≤1Impact Resistance/kg·cmGB/T 1732≥50Pencil Hardness/GradeGB/T 6739≥HTheoretical Coverage30-40um (based on dry film thickness)8-6m2/kgNote: The data listed is based on factory batch production products, and there will be slight changes due to different colors and batches.Construction condition parametersPaint mixing ratio (mass ratio): A: B = 6: 1Component A: Main paintComponent B: Curing agentDiluent: Deionized water/clean tap waterMaturation period: 3-5minActivation period: 4.0h (10±2oC) / 2.0h (25±2oC)Note: All data are valid only for mixed paint.Construction technologyConstruction technology Construction method: Thinner ratioSpraying Use airless spray or air spray with a cross-cross method. 0-10%Brush/roller Apply with a brush/roller with a cross-cross method. 0-5%Spraying methodSpraying type Spray gun diameter Spraying pressure Spray gun distance Spray fan widthAirless spray: 0.017-0.025inch 15-25Mpa 30-40cm 25-50cmAir spray: 2.0-3.0mm 0.4-0.6Mpa 20-30cm 15-25cmDrying and curing timeBake (actual drying): 80oC/90minNatural dryingTemperature 5oC 15oC 25oC 35oCSurface (touch) dry 90min 75min 60min 40minActual drying (trampling) 39h 34h 30h 22hRe-coat after drying 6h 4h 3h 2hDry to cure 9d 7d 6d 4dNote: 1. The above drying and recoating data are based on a paint (dry) film of 40±5um, relative humidity ≤60±5%, and natural drying conditions;2. Surface (touch) dry: no fingerprint residue or no adhesion when lightly pressed with fingers.3. Actual drying (trampling): the shortest time that the coating can allow normal walking without leaving permanent footprints, marks or other physical damage.4. The determination of drying and curing time is based on temperature and relative humidity, relative humidity ≤80%, and dry film thickness within the average dry film thickness range.5. Recoating after drying, shortest interval: the recommended shortest time interval for the construction of the next coat.6. Dry to solid and usable: the shortest time that the coating can be permanently exposed to a specific environment/medium.SC-HP4305Water-based two-component acrylic polyurethane topcoatPackaging specificationsComponent A: Water-based two-component acrylic polyurethane topcoat 20kg/barrelComponent B: Curing agent 4kg/barrelProduct parametersItemTest/StandardDescriptionColor/CodeGB11186Medium GrayAppearanceVisual InspectionSmooth and FullFineness/umGB/T 6753≤25Solid Content/%GB/T 1725>42Density/g/mlGB/T 67501.25±0.1Gloss (60° GU)GB/T 975490±5°Adhesion (Cross-Cut Test)/GradeGB/T 9286≤1Impact Resistance/kg·cmGB/T 1732≥50Pencil Hardness/GradeGB/T 6739≥2HTheoretical Coverage30-40um (based on dry film thickness)9-6m2/kgNote: The data listed is based on factory batch production products, and there will be slight changes due to different colors and batches.Construction condition parametersPaint mixing ratio (mass ratio): A: B = 5: 1Component A: Main paintComponent B: Curing agentDiluent: Deionized water/clean tap waterMaturation period: 3-5minActivation period: 4.0h (10±2oC) / 2.0h (25±2oC)Note: All data are valid only for mixed paint.Construction technologyConstruction technology Construction method: Thinner ratioSpraying Use airless spray or air spray with a cross-cross method. 0-10%Brush/roller Apply with a brush/roller with a cross-cross method. 0-5%Spraying methodSpraying type Spray gun diameter Spraying pressure Spray gun distance Spray fan widthAirless spray: 0.017-0.025inch 15-25Mpa 30-40cm 25-50cmAir spray: 2.0-3.0mm 0.4-0.6Mpa 20-30cm 15-25cmDrying and curing timeBaking (actual drying): 80oC/90minNatural dryingTemperature 5oC 15oC 25oC 35oCSurface (touch) dry 90min 75min 60min 40minActual drying (trampling) 36h 32h 28h 22hRe-coat after drying 6h 4h 3h 2hDry to cure 9d 7d 6d 3dNote: 1. The above drying and recoating data are based on the paint (dry) film of 35±5um, relative humidity ≤60±5%, and natural drying conditions;2. Surface (touch) dry: no fingerprint residue or no adhesion when lightly pressed with fingers.3. Actual drying (trampling): the shortest time that the coating can allow normal walking without leaving permanent footprints, marks or other physical damage.4. The determination of drying and curing time is based on temperature and relative humidity, relative humidity ≤80%, and dry film thickness within the average dry film thickness range.5. Recoating after drying, shortest interval: the recommended shortest time interval for the construction of the next coat.6. Dry to solid and usable: the shortest time that the coating can be permanently exposed to a specific environment/medium.Product DescriptionOur AdvantagesCompany ProfileFounded in 2016, Jiangsu Shuocheng New Material Technology Co., Ltd. is an environmentally friendly technology enterprise that specializes in the research and development, production, and sales of water-based paint products. The company is precisely positioned in the mid-to-high-end water-based paint market, committed to becoming a leading brand in this field, with the sacred mission of providing high-quality, high-performance, and environmentally friendly water-based paint products.Located in the Xuzhou National High-tech Industrial Development Zone, a state-level high-tech industrial development zone approved by the State Council, the company not only has an independent research and development institution but also owns proprietary intellectual property rights. It has established long-term and stable cooperative relationships with several well-known scientific research institutions. In addition, the company has successfully obtained ISO9001 Quality Management System, ISO14001 Environmental Management System, and ISO18001 Occupational Health and Safety Management System certifications, fully demonstrating the company's high standards and strict requirements in quality management, environmental protection, and employee occupational health.The company's main products cover various systems of water-based paints, including water-based acrylic systems, water-based alkyd systems, water-based epoxy systems, water-based acrylic polyurethane systems, water-based amino baking paints, etc. These products are widely used in many industries such as architectural decoration, machinery manufacturing, hardware and electrical appliances, automobiles, and ships.With advanced production equipment, strong technical strength, and comprehensive after-sales service, the company has firmly established itself in the water-based paint field with its exceptional product quality and precise market orientation. Several products of the brand "Shuocheng Waterborne Paint" have been awarded national invention patents, standing out in the fiercely competitive industry.At this stage, the company is actively expanding market share and enhancing brand awareness. It plans to achieve a significant increase in the market share of domestic mid-to-high-end water-based paints in the coming years and gradually explore international markets.The company always adheres to the concept of "lucid waters and lush mountains are invaluable assets," strictly controlling quality from the source of the product supply chain. It unswervingly strives to provide high-quality water-based coating products and considerate services for customers and society, aiming to set a model for the green development of the industry and contribute to the construction of a beautiful China.CertificationsFAQQ1, Are you manufacturer or trading factory?A: In fact we are the factory 10 years, can supply all types of paint. Q2, If the OEM is accepted?A: Yes, OEM is welcome. We also can do your own logo and package. Q3, If I do not know which paint to choose, what shall I do?A: Please no need to worried about this, we have the professional engineer, colorist, and experienced sales, can give you the suggestion for paint and coating. Q4, What's are your payment term?A: We can accept the TT, Western Uniono, LC, Credit card, and Alipay, and others please contact with us freely. Q5, Can you accept to supply the free sample?A: Yes, of course we are glad to supply the free sample, and you need in charge of the freight cost. Q6, What's your products' advantages?A. Good quality and competitive prices.B. Strictly quality control when producing.C. Professional team work, from design, development, producing,assemble,packing and shipping.D. Experience for shipping the paint to different countries. Q7, Can we visit your factory?You are Warmly welcomed to visit our factory, it would be our great pleasure!

× More Keyword ..

× More Menu ..

×

Manufacturing & Processing Machinery

×

Industrial Equipment & Components

×

Tools & Hardware Products