IPDB › China Industry › Instruments & Meters
China, Chinese 24V UV Indoor Flame Detector 2/4 Wire Fire Alarm Smoke Detector Nc No Optional1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
Fire ControlFire Alarm Smoke DetectorHeat SensorSmoke Alarm
Shenzhen Xinhean Technology Co., Ltd.
Preview:
Product Description Introduction The device is an Ultraviolet-only flame detector designed to detect fires and provide alarm outputs directly from the detector while maintaining false alarm immunity. It detects in the ultraviolet (UV) spectral range for optimized speed of response. It is fast and capable to detecting the ultraviolet (UV) rays emitted by a burning substance and is used in high hazard applications such as petrochemical plants, munitions factories and other areas where flammable or explosive liquids or solids are handled or stored. The flame sensor adopts an ultraviolet photosensitive tube, with qualities of highly sensitive, reliable, dust-resistant, corrosion proof and moisture-resistant, therefore is not sensitive in sunlight, dust, oil, tolerance of fume, and humidity. Set in a standard calibration to detect a flames at a distance of 25 meters, which flame created by 2Kg ethanol in a Container of Base 33cmX33cm, Height 5cmSpecification Operating Voltage Range: 12 to 28 VDC Volts Standby Current: ≤10 mA @ 24 VDC Alarm Current ≤30 mA @ 24 VDC Spectrum: 180~290nm Detection Angle: 120 degree Detection Sensitivity: Grade I, 25m@flame (Container 33cmX33cm,Height 5cm with 2Kg ethanol ) Relay Contact Load: 1A@DC24V Normal Status: LED blinking in 5 seconds interval Alarm Status: LED lit steady Protection rating: IP 21 Operating Humidity Range: 10% to 93% Relative Humidity, Non-condensing Operating Temperature Range: -20°C to 55°C Height: 45 mm installed in Base Diameter: 103 mm Weight: 153g Installation NOTE: All wiring must conform to applicable local codes, ordinances, and regulations. Mounting Indoor Wall or Ceiling Products.1. Attach mounting base to ceiling or wall. 2. Connect field wiring to terminals: Terminal 1: Relay Output -COM (ZONE+) Terminal 2: Relay Output - NO/NC (ZONE-) Terminal 3: DC Power - Terminal 4: DC Power + 3. To attach product to mounting base. 4. Secure product by tightening the two mounting screws in the front of the product housing. 5. The detector can be connected with Security alarm panel as Figure3. Relay output signal can be changed from Normal Close (NC) to Normal Open (NO) by Jump JP1 on the PCB board. 6. The detector can be connected with conventional alarm panel as Figure 4. One 4.7K ohm resistor should be connected as End of Line (EOL) resistor at the last detector. 7. After the installation, power on the detector, use lighter or candle to test the detector within 3 meters. WARNIING: Not to install flame detector near the below subjects: 1. Halogen lamp, Electric discharge lamp, ultraviolet ray lamp. 2. Welding spark, Electric spark 3. Heavy current magnetic field, thunder discharge. 4. Direct sunlight. 5.Ultra violet radiation subjects The UV flame detector can not detect the following: 1. The flame behind the glass or transparent resin. 2. Lighted cigarette. 3. Burning charcoal and coal cakes. 4. Burning material without flame.Application in Conventional Fire Alarm systemProduct RangeSmart Home Standalone smoke detectors and combustible/CO gas detector4 wire smoke detectors with relay output.2 wire smoke and heat detectorsExplosion-proof product for fire alarm systemConventional Fire Alarm SystemAddressable fire alarm systemExtinguishing control systemWireless alarm systemElectrical fire monitor systemFire door monitor systemFire extinguishing Water cannon SystemIndustry 4 in 1 Gas detector/ Single gas detector(CO/CO2 etc)Service1. OEM &ODM service.2. Provide technical support and after-sale service.3. 1 year warranty.4. Normally 15 working days lead time.5. Welcome sample order.
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...