IPDB › China Industry › Industrial Equipment & Components
China, Chinese Premium Silicone Heating Pads with Sturdy Aluminum Base for Comfort1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
Heater Heat ExchangerHeating EquipmentDurable Aluminum PadSilicone Heating Pad
JPCI Controls (Foshan Gaoming) Co.,Ltd
Preview:
Product Description Recommended by seller JPCI Type 9AB Silicone Rubber Heating Belts for Metal Drums, with Surface Mounted Bulb and Capillary Thermostat$59.00-285.00/ piece 5 pieces JPCI 9SU107 Max Power 1500w (10W/cm2) 3000w (20W/cm2) 70mm Diameter, Length 70 mm Standard Liquid Heaters$20.00-60.00/ piece 100 pieces JPCI Type 9V46004A Metal Drum Base Heater for Drum 200L$403.84-417.51/ piece 1 piece JPCI Jacket Heater for 20L 5 US Gallons Plastic Container 9VJCD301028015J3$122.63-175.19/ piece 1 pieceJPCI Type 9AM Non flexible silicone heaters vulcanized on aluminium board, with remote electronic temperature control,double display, PID action.Product DescriptionMain Features Non-flexible silicone rubber heaters are made of fiberglass reinforced laminated silicone rubber sheets, vulcanized together through heat and high pressure on both sides of an embedded specially formed heating wire element. Fiberglass-reinforced silicone rubber gives the heater dimensional stability.The intimate bonding of the heater on a thick aluminum plate allows to increases the power surface load, and eases the mounting on flat surfaces in industrial applicationsSilicone is used because of its high temperature resistance (Permanent temperature up to 200°C (390°F), high thermal conductivity (~7 10-4 W/cm.K) and good electrical insulation properties (~12KV/mm)This series is distinguished by the use of a remote electronic control system, on-off action, simple to use, with digital display of the measured value, connection by waterproof connector for easy disconnection of the heater, and IP65 ingress protection class for the whole assembly. This allows its use in most of industrial applicationsOther general particularities of these heaters are:- Not affected by vibration or flexing,- Light weight,- Comply with U/L94-VO (flame retardant) and ROHS,- Low smoke and low Toxicity,- Silicone is non-toxic, and moisture and chemical resistant. Main ApplicationsSilicone heating elements on aluminum plates are a simple and industrial solution for heating flat surfaces. They are sturdy, easy to install and heat quickly and evenly. Some typical examples of applications are: Heating of hoppers, electrical cabinets, hot plates for the food industry, reheating tank bottoms.In addition to their temperature control system, they can receive temperature sensors, temperature limiters, thermal fusesTechnical Features Mounting: By 4 holes dia. 12mm located at the 4 corners, at 15mm from edges.Length (Dimension A): Upon customer request (minimum 300mm).Width (dimension B): Upon customer request (minimum 100mm).Ingress protection: IP65.Minimum ambient temperature: -10°C (+15°F)Voltage: 220-240VAC.Power tolerance: ±10% at 20°CTemperature control:By electronic controller with digital display, On-Off action, set point adjustment range up to 120°C (NTC sensor), or 200°C (Pt100 sensor), relay output, located in an independent waterproof housing, designed for wall mounting. It is connected to the flexible silicone rubber heater by a cable equipped with a 5-pin waterproof quick connector, facilitating the connection and disconnection with the heater. It controls the temperature by means of a probe placed under a silicone boot on the outer surface of the heater.Action: PID with automatic parameters adjustment by auto-tune function.Sensor input: Pt100Power output: solid state relay, maximum 16A 230V.Alarm: 3A 230V relay.Display: 4 digits display configurable in °C or °FPower supply: AC 220-230V 50-60Hz.Accuracy: ±1°C (±2°F) or 0.3% ES± one digit.Self-testing: open sensor circuit.Ambient temperature: -10 to 60°C, 20 to 85% relative, humidity, non-condensing.Temperature display range: ConfigurableResolution: 0.1°Read instruction manual before the setting of this temperature controller.Power density:- 0.2 w/cm2 (1.3W/in2) for plastic materials- 0.75 w/cm2 (4.8 w/inch2 ), for usual applications.- 1 w/cm2 (6.5 w/inch2 ) for fast heating applications.- 1.4 w/cm2 (9.1 w/inch2 ) for huge power applicationsOther values on request.Thickness of the flexible silicone foil: 2.5mmThickness of the aluminum board: 6 mm (other values on request).Quality control routine tests: Each element is 100% tested for continuity, resistance and insulation. Tests are made according to EN 60335-1 and EN 50106 standards. See technical introduction.Dielectric Strength: 1750V AC.Insulation resistance: ≥ 10 Megohms.Operating temperature:See in the technical introduction examples of the temperatures reached by these heaters. They represent the temperature that they may reach if they are not correctly installed.Connection cable:Insulated rubber power supply cable, for industrial environments, 3 x 1.5mm2 (3xAWG15) length 3m, Euro plug. UL plug on request.Options:- Power supply 110/115V- Power cord with industrial plug 2-pole + earth 16A CEE (IEC60309).- Surface mounted temperature limiter.- Grounded mesh wire shield layer- Silicone foam insulation layer vulcanized on the external surface. Safety standards: The heaters have been designed in compliance with EEC Low Voltage Directive (LVD) 2006/95/EC and EMC directive 2004/108/EC. They must be installed in accordance with all local applicable instructions, codes, and regulations. Main parts numbers in 220/240V * For UL plug instead of Euro plug, replace F3 with E3 in the part number. Packing&ShippingOption : By air & By sea & By truckCompany IntroductionCompany profile:Established in China since 2000, with French technology and investment, our company is proud to have more than 60 years experience in manufacturing electromechanical components and 30 years experience in manufacturing safety component for Spas, swimming pools and hot tubs. This experience, combined with high tech equipment and high tech raw materials let us develop the new components needed by rapid expansion of Asian and Chinese market.In our new factory, on more than 8000 square meters production lines, we have two manufacturing divisions:Division one is producing components:Thermostats, energy regulators pressure switches, level switches, flow switches, fire detection fusible links, heating elements and ceramic connection blocks.Division two is producing complete assemblies and sub assemblies on customer specifications:Swimming pools heaters, heat pumps backup heaters, spas heaters, small water heaters, immersion heaters, aluminum foils heaters, baseboard and convection heaters sub assembliesOur R&D team develops new products upon customer specification, taking care of international safety standard (UL, CE, etc.).We produce our own stamping, bending, plastic injection, zinc alloy injection, and machining.We are equipped with up to date automatic and CNC TIG welding and laser welding equipment and ultrasonic welding checking.We have our own climatic room, corrosion testing loops, salt spray testing, and more than 30 specific equipments for products life testing.Our income quality control laboratory is equipped to check raw material (plastics, metals) physical characteristics and dimensions.Our finished product control laboratory has more than 200 machines to calibrate and check temperature, pressure, level and flow controls.From the raw material to the finished product we control every production step. Meet your control equipment demand rapidly and safely is our consistent promises.Basic Information Product/Service Sell: Flow switches, level switch,pressure switch, thermostat,heating elements, back up heaters for heat pumpsNumber of Employees:200 to 300 PeopleMain Markets:North America/South America/Eastern Europe/Southeast Asia/Africa/Oceania/Mid East/Eastern Asia/Western/Europe/Northern Europe/Southern Europe/Domestic MarketTotal Annual Sales Volume: US$2.5 Million - US$5 MillionExhibitionDomestic : China Heat Pump Exhibition ,Shanghai city , 15th-17th March every year Oversea : It depends,normally in Europe,
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...