IPDB › China Industry › Manufacturing & Processing Machinery
China, Chinese Paper Gluing Machine/ Kraft Paper Impregnation for HPL Paper1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Industrial Products Supplier Manufacturer List Catalog
Paper Making MachineMelamine Paper Making MachineMelamine Paper Impregnation
Wuxi Qiangtong Machinery Co., Ltd.
Preview:
Product Description 1.1 ApplicationsThe paper impregnation line use urea formaldehyde resin, phenolic adhesive to impregnate, coat, dry and stack paper base material.With the decorative paper impregnation line, for the production of:Melamine resin impregnated papers, for the Low-Pressure Laminates (LPL).Melamine resin impregnated overlay paper, decorative paper and balance paper for flooring.Melamine resin impregnated overlay paper for the High-Pressure Laminates (HPL)Phenolic resin impregnated paper for plywood lamination.1.2 Scope of applicationThe production line use fixed amount 40 ~ 250g/ square meters, width 900~1400 mm melamine/phenolic paper. The wet strength of melamine/phenolic paper is not less than 0.75kgf/15m.1.3 Environment for line runningThis production line is suitable for no corrosion and water soluble resin (Like urea resin, melamine and phenolic resin)High-temperature resistant requirement: F level, Explosion-proof gradeEnvironment temperature: 10~40oCRelative humidity ≤90% (Temperature at 20oC)Altitude not more than 1000m Part 2: Impregnation line parameters2.1 General parametersModelNTC1500A-2-3 Two Steps LineWidth of raw paper900~1400 mmMax. roller width1500 mmMechanical speed4~100 m/minWorking line speed15~18 m/min for melamine resinWorking height1350 mmHeating methodThermal oilDryer working temperature120~180oC2.2 Dimensions Raw paper roll diameterφ1100 mmWeight of roll paper1200 kgIn-diameter of paper axis3''(76mm)Dryer length3750 mmEffective drying length(2+3)× 3750=18750 mmEffective drying width1500 mmTotal line length~44,000 mmTotal line width~3800 mmTotal line height~4500 mmTotal line weight~46,000 kgsOperating areaOn the right side, run along paperDriving areaOn the left side, run along paper2.3 Power and energy consumptionDriven power3 phase,380V,50HzControl power2 phase,220V,50HzTotal installation power~125 KWHeating mediumThermal oilCompress air pressure0.5~0.7 MpaCompressed air consumption~8 m3/h as the installation volumeCooling water pressure0.2~0.4 MpaCooling water consumption~8 m3/h at 45 degree temperature weather which means biggest volume, This is calculated by 60m/min speed volume, if line speed is 30m/min then means only consumption 4m3/hRemark: Compressed air volume means max. Demand which means at maintaining when all the cylinders are open need 8m3/h also means installation volume. While the normally running consumption is 0.5 m3/h. But when paper is broken or changing paper, need to open all the doors then that time consumption is 2m3/h. So to make sure the line can be worked at all conditions, need to prepare the 8m3/h compressor. 2.4 Line capacity calculationThe real capacity of this model impregnation line not only depends on the design of the machine, but also depends on the glue mixed, paper quality, and the temperature of working environment, wind capacity of recycling fan, the mature operation of the workers etc.Calculation is based on:ResinMelamineTemperature inside oven120~180oCRaw paper density80 g/m2Raw paper width1300 mmResin contain of impregnated paper130%~150%Volatility of resin6~7%Working line speed20 m/minWorking time330 days/year x 3 shifts/day x 8 hours/shiftProduction capacity per day for 4x8 feet paper:15 m/min / 2.5 m x 60 mins x 20 hours = 7200 sheets papers per day at least. Part 3: Details of supplied machinery3.1 Semi-auto unwinder This unwinder is scroll type with two-axle type, it is equipped with two inflatable roll and safety chuck. When uncoiling, magnetic particle damping device could offer enough tension to paper. This machine has paper receiving device. It can make the new roll of paper to stick to the end of last roll of paper without stopping the machine, the high-speed cutter can cut the rest of last roll of paper to achieve continuously impregnating. One staff is enough for paper receiving.Including: frame, aluminum roller, damping device, paper receiving device, 2 set two cylinders' roller inflatable gas system, 2 set electronic magnetic powder brake and safety chuck. 3.2 Impregnator (First step dipping)Impregnating machine consists of frame, coating section, breathing system, impregnating roll unit, meter device, glue tank and heating device for glue tank etc.This impregnating machine is used in first impregnating. Using coating roller to do the single down side coating for the paper, angle size of coating is adjustable, then resin glue will penetrate into the paper from down side, and drive out the air from upper side completely. The coating device is equipped with breathing system, according to the different requirement for raw paper, resin glue and impregnating ways, the breathing system can control and adjust the height of breathing section, in this way to make the paper reach to enough amount of glue and adjust the flatness of paper. Resin infiltrate into the paper fabric and less low down the wet tensile strength, then the process of impregnating can go smoothly.Raw paper will be feeding into the glue tank after coating section and breathing section. Adjusting the gap of metering roll can control the resin content and impregnating uniformity of bond paper accurately, the motion accuracy of metering roll is ≤ 0.003mm.Configuration technical requirements: includes frame, S roller, Back coating part, Impregnating roller part, Metering roller φ290, Metering device, breathing system, the middle part of stainless steel (430) glue tank with spacers, the glue tank lifting and lowering is controlled by a worm gear reducer, and the metering roller adopts NSK bearings imported from Japan, the wall thickness of the roller can not be deformed, (the upper and lower motors of the breathing roller).It consists of:a) Frame structureb) Back side coatingc) Breath partd) Impregnator parte) Squeezing partIt has automatic and manual both operation model.In manual operation, the controller is in one side but can adjust two sides.In automatic model, it can adjust automatically by setting value through cabinet panel beside it.The gap between the squeezing rollers are shown in the screen, and you can adjust.It consists of below rollers:2 pcs steel roller with chromed surface with Φ290mm diameters, 3.5mm tube thickness, jumping accuracy is < 3 um under 100m/min speed, 0.3mm chrome surface and it has 50 CR hardness. f) Glue tankg) Glue tank heater 3.3 Dryer (6 sets Ovens) Pneumatic automatic big door for easier operation and better heat preventing;Three-layers heat insulations design to save energy 20% at least; 3.3.1 Drying ovens The machine consists of drying section, dehumidification system, automatic door, temperature control system, etc. The length of each drying section is 3750mm.The heating medium of the drying section is thermal oil or steam or natural gas direct burning system. According to the requirements of the drying process, each drying section is a temperature zone. The working temperature can be set independently and the temperature of the zone can be automatically controlled by the temperature control system, so that the actual temperature is basically consistent with the set temperature. ; The temperature is generally controlled between 120 and 180 °C. Each drying section has a wet outlet, and the opening of the wet outlet is controlled by a manual damper, and the operator sets the opening according to the process requirements. 3.3.2 Drying oven structure The frames of each drying section and air curtain section are welded parts of rectangular steel pipes and square pipes (50/100), with high strength and small deformation. The drying section is composed of bellows, air ducts, specially designed nozzles, hot air blowers, threading chain guides, etc. The frame is surrounded by thermal insulation wall panels and thermal insulation doors, and the thermal insulation doors are double-sealed and manually opened. Each section of the drying section has butterfly dampers up and down the hot air duct, the insulation layer is 15cm, 2 cold plates are used for the outer side, 2 galvanized sheets are used for the top plate, and 2 galvanized sheets are used for the inner side and the air duct plate.No.NameQty.ValueNote1Hot wind fan5 setsWFF-8.6# Motor5 setsY132M2-4 PowerKW15Has inverter2Moisture dryer fan1 setWFF-9.0# Motor1 setY00L1-4Liddell/BeidePowerKW22 3Hot air exchanger5 pcsTOCC-SR-01 Nozzle50 pcs import patterns4Platinum thermal resistance wire5 pcsPt100Press plenum6Temperature meter5 pcs America HONEY7Gas burner (If gas type)5 pcs Chinese brandSupply range: Drying units, moisture exhauster3.4 Roller Coater (Second step coating) The machine consists of frame, upper and lower mesh coated squeegee device, the second smoothing device, lifting devices. Second over coating machine is used to make paper coating liquid surface covered by the smoothing process requirements after reaching the glue. This machine is used twice on the plastic, paper tape into the secondary coating coater, and then the upper and lower for recoating, the surface evenly covered with glue. (Note: choose accurate mesh size, which directly affects the amount of secondary glue) Then it is smoothly polished to ensure the tape is even and smooth when it goes into the secondary oven.Configuration requirements: upper and lower roller coating change speed frequency and converter speed. Smooth roller adopts cylinder lift, frequency positive and negative control, high and low angle can be adjusted on a smooth, plastic tank made of stainless steel (S430), roller bearings use imported NSK. No.NameQty.ValueNote1Reducer1 setK47-2.2kWTop coating2Reducer1 setK47-2.2kWBottom coating3Upper coating roller1 setR27-1.1kW 4Lower coating roller1 setR27-1.1kW Supply range: Frame, upper and lower coating machine. The machine take mesh coating. 3.5 Cooling Unit The paper is taken out of the drying section and entered into the cooling section. The length of the cooling section after drying is 3750mm, which is mainly composed of rack, sealing plate, air box, air duct, cooling heat exchanger, nozzle, circulating fan, moisture exhaust air outlet, etc. The upper and lower air volume can be adjusted separately through the air door.No.NameQty.ValueNote1Cooling fan1 set Motor1 set7.5 kW 3.6 Web alignerPaper tape will run deviation after long distance operation, so after move out of the drying section, the alignment machine can bring the paper to the middle position. Upper supporting rollers adopts movable roller, and lift by cylinder.No.NameQty.ValueNote1Photoelectric deviation rectifying system1 setPrecision control Detector E3Z-D622 sets OMRON 3.7 Pulling machine (Dia. 800mm) The tractor not only provides power for the normal operation of the paper strip, but also has the function of further cooling the high-temperature paper strip coming out of the dryer to a suitable temperature for subsequent processing. The traction rollers are two cold water rollers of φ800mm, two φ350mm and φ200mm, and cooling water can be passed through the rollers. With cylinder platen roller.No.NameQty.ValueNote1Reducer1 setK57-4kWPulling roller2Reducer1 setK57-4kWPaper chain 3.8 Rotate CutterA pair of paper feed rollers are set up and down in front of the shearing knife, and the fixed-length cutting is realized by the action of the paper feeding roller and the cutter. The upper and lower pressing rollers are guided by linear bearings and lifted by the air cylinder. The speed of the feeding rollers is adjustable and is set at the edge of the feeding paper, which is convenient for adjusting the tightness of the paper. Can be cut from 18g to 200g paper. Can set automatic counting alarm, adjust the length at will. And equipped with positioning shearing device.No.NameQty.ValueNote1Reducer1 setR47-4kWFeeding roller2Reducer1 set4.5kWFor cutter3Encoder1 set2000POrmon 3.9 Paper output stacking table 1 set and lifting table 1 set (Belt with lifter type) Function: Paper sending drive, adjustable paper sending speed, easy to stacking, convenient out feeding, lifting up and down and can bear the 3 tons weight.No.NameQty.ValueNote1Reducer1 setKAT37-2.2KWConveyor2Air blower1 setCZR-68, 250Shanghai3Lifting motor1 setY90L-4/2.2 kW Supply range: lift-valve, Hydraulic lifter, frame, roller conveyor, and belt and power device. 3.10 Electrical control system The electric control system includes 4 sets electric control cabinets, one-time dip touch control cabinet, paper pick-up control cabinet, and shear count control cabinet, which are mainly composed of the following control units.(1) The main drive control system adopts Mitsubishi frequency conversion control system.(2) The hot air circulating fan is controlled by frequency conversion speed regulation.(3) In addition to the emergency stop button on the main control electric control cabinet and the fuselage operation station, there is a pull wire emergency stop switch at the appropriate position of the production line, and the wire connection must be uniformly numbered according to the electrical drawings.Electrical control configuration and informationNameSpecificationQty.BrandPLCFX3U1 setMitsubishiTouch panel10.44 setsBukeInverterS roller motor inverterD7401 pcsMitsubishiBack coat roller motor inverterD7401 pcsBreath roller motor inverterD7401 pcsGlue rollerD7401 pcsPaper chain gearbox and motorD7401 pcsPulling roller motor inverterD7401 pcsSmooth rollerD7401 pcsSecondary coater motorD7402 pcsSecondary smooth motorD7401 pcsPaper pull motor feed motorD7401 pcsServo cutter DeltaHot wind fan motor15 kW6 pcsINTVMoisture exhaust fan22 KW1 pcsOther electrical partsPhotoelectric switchE3JK-DS30M11 pcOMRONE3Z-D622 pcsGetting touch switchTL-Q5MC11 pcs5 pins coderE6B2-CWZ6C1 pcTemperature controller valveDN506 pcs hot resistancept1006 pcs Temperature controller meter 6 pcsHoneywellPower supply 3 pcsDelta, TaiwanAC contactor 11 pcs Power switch 25 pcsAir switch 1 pcsLimit switch 5 pcsStart/Stop button 40 pcsNo.NameSpecification1Electrical power wireRVV3x102Electrical power wireRVV3x63Electrical power wireRVV3x2.54Electrical power wireRVV3*1.55Electrical power wireRVV6x0.56Electrical power wireRVV4×0.57Shielded wireRVV10×0.58Shielded wireRVV6x0.5Safety suggestions:Supplier offer safety system to avoid damaging operator and equipment.Cover all rotating wheel and gear.The safety line below measuring roller should be connected to the emergency stop device.Set up a preventing tripping bar / system for the metering roller to avoid finger or others being tripping.The wire must be protected by a wire slot or bushing. National standard wire is necessary. Other components brandComponentsBrandReducer and motorTGSAir cylindersSMCBearingKey parts NSK Part 4: Supplied by the buyer sideVenues, buildings, equipment, installation tools, equipment, installation materials such as: anchor plate, plate, Rod, steel structures, standard parts (bolts, nuts, washers, etc.).Standard installation tools and equipment such as welding machines, cranes, hoists, and other hand tools.Cleaning equipment and tools.Safety protection devices of fire-fighting facilities.Material transport and handling equipment, such as truck, driving, etc.Workplace power distribution and power systems, power distribution Cabinet.Moisture exhauster insulation works.Reached the production line of compressed air pipe.To line master workshop of the electric control box cable.Electronic control systems and equipment grounding facilities.Workshop machinery and electrical equipment, machinery and tools.Spare parts, wearing parts, consumable materials, raw and auxiliary materials, such as the storage place facilities.Debugging using the paper, rubber and other raw materials. Part 5: Duties from the supplierAll the cables and connectors between the main electrical controlling cabinet to the working line.Moisture exhauster pipesAll the machine parts must be new made, any second hand is forbidden. Part 6: Quotation of standard impregnation lineModelNTC2100A-2-3 Two Steps Line Equipment ListNo.NameQty.Unit1Semi-auto unwinder1Set2Paper impregnator (Dipping)1Set3Dryers (auto door)5Sets4Second coater1Set5Cooling unit (with exhaust unit)1Set6Web aligner1Set7Pulling machine1Set8Rotary cutter1Set9Belt conveyor with lifer for stacking1Set10Electrical control system1SetTotal Amount196,000.00 USDSay untied states dollars one hundred and ninety six thousand onlyPrice TermFOB Shanghai, ChinaDelivery Time100 days after receiving deposit, excludes Chinese statutory holidays.Payment Terms30% deposit, 70% paid before delivery, this is negotiable term.Transportation cost & InsuranceAt the buyer's side, not include in above offered priceQuality TestAfter getting all equipment, buyer should ensure all conditions for installation and commissioning of equipment within 20 daysAfter finishing installation and test, buyer need to offer receiving report within a week. Otherwise equipment is deemed to be qualified.Without supplier promise, buy could not using equipment. Otherwise equipment is deemed to be qualified.Installation and commissioningInstallationInstallation and commissioning is guided by sellerThe quotation doesn't include all the costs related to the installation work.Guiding installation and test fee: 200 USD per day per personRound flight tickets & Board & lodging are covered by the buyerThe cost of quarantine or post-infection treatment due to the corona in the buyer's country is under the buyer's side
Purchasing Request
Note: Send your purchase request, and we will screen suppliers or manufacturers for you free of charge...